JGS968SH5SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara J from Sweetwater, TX
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Missing grate foot.
Ordered by phone parts & very pleased with all of transaction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Kenner, LA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate Foot Have 8 For My Stove And One Breaks Every Now And Then
This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fadel from Visalia, CA
- Parts Used:
- WB03T10197
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
so easy
the repair takes 10 sec, as long as you choose the right model...... great service from partselect... delivery within 48 hours.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jud from gatesville, TX
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
F2 error code
Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Stuart, VA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic slide for storage drawer broken.
Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Salem, OR
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Flashing F2 and erratic temperature readings.
Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Woodinville, WA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Our bottom drawer support broke and the bottom drawer was canted
Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from San Diego, CA
- Parts Used:
- WB13T10045, WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broiler and Burners would light, oven would not light and you could smell gas, also before the oven stopped working the oven was taking awhile before it would light
1.Removed the oven door. 2. Removed the oven floor panel ( slides right out ). 3. Removed cover plate and and removed one screw holding the igniter in place. 4 was able to pull the wire into the oven and unplug the igniter. Ordered a oven temp sensor but never needed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Munt Laurel, NJ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Probe broke
Ordered new probe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Lansdale, PA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hard to move drawer in and out because the rear drawer supports broke off.
Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vaughn from Visalia, CA
- Parts Used:
- WB13T10045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Stove top worked, Broiler worked, but Oven would not heat
Odered igniter from part select, it arrived the next day. Removed oven door removed heat shield on bottom of oven and there it was. Removed the two screws pulled the wires till the connector came through, unpluged connector, plugged in new igniter, repaced everything and Bam, we were cooking. Did not even have to pull oven out from the wall. Super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gino from glen ellyn, IL
- Parts Used:
- WB13T10045
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
faulty igniter
No response from GE website (very disappointing). google "repair GE gas range igniter" and very simple step-by-step instructions...apparently is very common with GE appliances...even mine that was less than 14 months old. Service tech would have charged $300. Did it myself for $80
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Salem, OR
- Parts Used:
- WB13T10045
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Ignitor burned out.
Instead of trying to remove ignitor while mounted to burner, I removed burner/ignitor assembly by detaching it from the oven frame and pulling the ignitor/burner assembly out so connector cleared the access hole. Disconnected and removed whole assembly. Then had easy access to the mounting screws. Removed screws by first spraying threads with WD 40 and waiting. Screws were oxidized so they were damaged when backing them out, as were the threaded mounting holes in the burner ignitor bracket. The screws are not sheet metal as noted in other posts, but rather are 10-32 machine screws. I chased the ignitor mounting bracket threads, then remounted the ignitor with 10-32, 3/8's, cap head, stainless bolts with a stainless star washer (available at any ACE hardware or other similar store) -- that way you don't have to tighten up so tight (just snug them up) -- unless you expect an earthquake every other week. The stainless screws helps retard the corrosion brought on by high heat and any moisture that settles on the bolt threads as the system cools and with subsequent starts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from New Concord, OH
- Parts Used:
- WB13T10073, WB16T10011, WB16T10032, WB04T10012, WB04T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Igniters on gas stove were randomly sparking.
Backed off screws that held the burner base over the gas opening. Removed C ring and spring and slid out old igniter, cleaned base, inserted new igniter and replaced burner gasket, refastened base and the job was done. Repeated for other for burners. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl F from Severna Park, MD
- Parts Used:
- WB13T10045
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Self Clean would not start, Broiler would not turn on,
Pull stove forward to access back. Remove center metal panel, 6 screws with 1/4" nut driver. Disconnect igniter connector. Measure resistance, it should be less than 1 ohm. Obtain new igniter. Test new igniter, 0.30 ohms. Remove oven door, see care and cleaning section of owner's manual. Remove burner cover, 2 screws with 1/4" nut driver. Remove two screws holding igniter. Aside: This is the second igniter to be replaced in this stove. The last one was exactly two years ago. Both times a screw snapped. With a small 5" vise grip the leading edge of the screw could be walked out. This time the two screws were replaced with 6-32 x 3/8" hex socket cap screws, split lock washer s under the screw head, and hex nuts holding the igniter in place. Note: All hardware was stainless steel. The burner cover was replaced. Oven door remounted. Igniter connected. Broiler turned on, it ignited. Center metal panel replaced. Stove moved into its nook.
Was this instruction helpful to you?
Thank you for voting!