JB968BK2BB General Electric Range - Instructions

very easy and clean.

Removed old switch, put metal jumper from old switch to new one and connected wires to the new one . Reinstalled. Works great.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Pulled the old one off (very easy), used popsickle stick to push first end in slot, aligned pins, pushed them in the holes and pushed other end in the slot.

Easy

popped the new one on!

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Replaced it

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

I got someone to look at the stove. They told me what I needed. I looked all over the Internet and couldn't find the part. One guy told me just to buy a new stove top because mine was an antique. It still looked good and two burners were still working. I didn't give up. I found the part on partselect bsite and was thrilled. It shipped fast and was exactly the right part. Now my stove works like new.

Turned off the power to the stove. Removed the oven door, Removed two screws holding the metal housing from the oven wall. pulled the assembly forward, removed the two electrical wires from the back of the socket, installed new gasket on back of metal assembly,inserted the wires thru the hole in the metal assembly, attached the wires to the new socket, pushed the new socket in place making sure the two holding clamps were in place, screwed assembly back in oven wall, replaced new bulb, replaced glass cover over bulb, Replaced oven door, turned the power back on, Light works like new.

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

Shut off power at the panel to the electric oven. Removed 2 phillips screws holding bulb unit in place in the top of teh oven chamber. One wire was so frayed it came out of the push on connector. Stripped off insulation and reinstalled onto the connector, using pliers to snug the wires down. Installed the new porcelain socket from Parts Select, replaced the unit in the top of the oven unit. Installed a new bulb, then snapped the new glass housing into place with the existing retaining wire clip. Presto: works like it's brand new. Thanks to Parts Select for the right parts, and for such quick delivery. I will use them again!

Open oven door, unlock hinges and lift off. Lay on face on carpet or piece of cardboard. Remove 2 screws at top that go thru door and hold handle assembly. Remove 3 screws on bottom that hold bottom door trim to inner door. Carefully turn assembly over (hold it together so you don't drop the glass front!) and place back on floor, hinge side down. Lift off front glass and frame assembly. Lay flat on floor. Remove 4 screws that hold bottom door trim to side frames. If glass is stuck to bottom door trim (which it probably will be from rust and gunk)..... Remove 4 screws that hold side frames to upper handle assembly and completely lift glass and bottom trim out. Holding glass vertical, stand on the bottom trim piece and carfully work the glass up and out of the groove (do not wiggle it side to side or you will need to buy a new piece of glass). While you have everything apart, clean all the parts and remove the decade of gunk. Reassemble in reverse. The long screws at the top of the door that hold the upper handle assembly in place, have spacers around them, they thread onto the screws and maintain distance and alignment when re-assembling. Also, I found it easier to remove the handle from the upper piece (4 screws) to allow me to lay the whole assembly flat while screwing the bottom, side, and upper trim pieces together around the glass front. Once that is done, then put the handle back on before you assemble it to the inner oven door. That is it !

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!