ZBD6920DSS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Astrid from MORAGA, CA
- Parts Used:
- WB16K10055, WB29K10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
THE OLD BURNER HEAD WAS NOT TURNING ON PROPERLY AND THE GAS CAME OUT UNEVEN.
I JUST EXCHANGED THE BURNER AND BURNER CAP.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wesley from FRANKLIN, TN
- Parts Used:
- WB13K10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Gas range igniter was making a clicking sound every 3 to 5 minutes, as if it was trying to ignite one of the burners.
Unplug the range from its wall socket to avoid electric shock. The various range parts that support a pot or frypan are easily lifted off their perches, exposing the small white igniter. The only moderately difficult aspect is wiggling the igniter out of its retainer. The electric wire leading into it then can be pulled out and fed into the new igniter with a push. Replace igniter in its retainer, then replace the range parts you removed to expose the igniter and plug the range back into the wall socket. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Coto de Caza, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Interior Light did not go on due to faulty switch
I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from Coto de Caza, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
switchlight on my refrigerator was not working
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard B from CLARKSBORO, NJ
- Parts Used:
- WB28K10222
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Large burner cap finish was damaged
Just lifted old burner off with my fingers and replaced with the new one. What needs to be focused on here is the fact that Part Select has such a complete line of parts rather than the difficulty in the install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Morris from HOUSTON, TX
- Parts Used:
- WB28T10278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bumper were old and broken
Pop old ones out and pressed in the new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karin from ARUNDEL, ME
- Parts Used:
- WB16K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gas burner wasn’t burning properly
I ordered the new burner head and replaced it and now it works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from WARROAD, MN
- Parts Used:
- WB16K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burner had hot spots where the matieral melted some cause a distorted flame that would spit sputter
Remove the top grate and remove the top burner plate and then pull the burner out and remove the torx screw and adapter install onto the new burner and place back on the stove , good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from CENTRALIA, IL
- Parts Used:
- WR23X37285, WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light kept blinking on and off never same way
turn breaker off first then use thin blade screwdriver and plastic pry bar to remove light socket and switch there was plenty of wire so work was easy to install at both ends
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from LAFAYETTE, LA
- Parts Used:
- WR02X11331
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Squeky Evaporator Fan
I made my wife fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Tacoma, WA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light wouldn't come out of socket
It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICKEY from MONTROSE, NY
- Parts Used:
- WB25T10041
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lens snapped off on the inside-plug was left loose
popped out the remainder of old lens, then pushed in new ones and slipped on plugs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Shelton, CT
- Parts Used:
- WR82X10103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
brand new ge refrigerator delivered with broken access cover. cost 6.95 so i repaced it myself.
removed 6 screws and repaced cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodi from Benton Harbor, MI
- Parts Used:
- WR23X37285
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light out
Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter M. from Lincoln Park, NJ
- Parts Used:
- WR02X10540
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Defroster fan burned up
First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.
Was this instruction helpful to you?
Thank you for voting!