JCB730DF3BB General Electric Range - Instructions

I ordered the correct part, the box said it was the correct part and when I opened the box a completely different part was inside. Not only was it the wrong part but it was loosely wrapped with very thin plastic and the hinge was broken off of the lid and laying in the box. I have called and emailed for help and was told no one was available to help because of COVID 19. One email was answered to return the part I would have to pay shipping and the part could not be damaged. Okay, the part was wrong, the part was broken. Now what should I do? Please respond.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

Removed top of washer. Three screws.
Removed control panel. Three screws.
Removed spring loaded ring which seals washer rubber gasket and door assembly. Disconnect door interlock connectors.
Removed front panel which includes door assembly. Three screws.
Access to pump is on lower shelf. Remove connectors from pump assembly. Remove clamps on two pump inlet/outlet hoses. Remove two screws holding pump assembly.
Install new pump assembly in reverse,

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

Replace the water valve according to the youtube video from this site. It was really easy!

Purchased parts per your diagram and went to a appliance store to see how it was assemble

First I locked out the power cord. I pulled the back screws to the top panel off, slid the top panel to the back of the washer, and pulled the top off. opened the washer door, and ran my down where the door switch was. with one hand on the switch, I use the other hand with a philips screw driver to remove the screws on the door switch. Pulled the switch up just enough to remove the electrical plug. Now installation will be the same but start backwards. Plug in the switch, run the switch into the housing. While holding the switch in place with one hand use the other hand to install the two screws. Replace the top panel, remove any lockouts.

It snapped in place.

After searching through appliance Mfg Company for parts for A few days. Some how I ended up at this Great website for Quality but inexpensive and half the price. Could not afford to pass up A great deal... Easy install within 5mins and no more headaches or worries. Highly Recommend it to Everyone out there.....

Loosen the two set screws. Remove old handle. Install new handle and tighten the two set screws. Job done.

I attached the new handle and tightened the set screws with an Allen wrench. Piece of cake!

my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.

utube video made this repair very easy! remove front lower cover, drain pump will be on the right, 2 screws hold pump in place (unscrew), remove hoses by using plyers to slap hoses off pump, remove old pump. replace with new one, screw back in, replace hose & claps. DONE!! i ran a rinse and drain cycle before replacing the front cover just to be sure there were no leaks.

Installing the part repaired the fridge and freezer immediately.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.