J2B918SEK2SS General Electric Range - Instructions

I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

watched the video on part select - took less time then they said.

Ordered new probe

I opened oven and pushed oven rack inside.

There were two small screws at the back of the stove (this was the part that intimidated me. At first glance it doesn't look like it should be removed). But you just have to unscrew them, disconnect the wires behind them (this part can be done by hand), and pull the element out. The new element slides right in! Just make sure the power to the stove is disconnected either by breaker or by unplugging it. I'm not sure if it matters, but I made sure to connect the wires to the same side of the element that they were removed from.

Saw the brief video and as stated took less than five minutes to replace. It took longer to clean up the floor under the oven than to replace heating element.

replaced

just slipped it in

plug in thermistor when needed

My oven is wired into the wall so I had to cut the power off at the fuse box. The hardest part was pulling the stove/oven away from the wall to see if it was a simple plug in or wired in. I lifted bottom drawer out so I could get leverage and lifted the entire unit so I could put the front feet on the soft pads. It slid away from the wall easily. I found a socket that fit the screws on the plate holding the broken element and unscrewed it, saving the screws. A gently tug on the element pulled the attached ends through the hole. The tip of the ends were attached to the wall wiring by a small sliding metal clip. I carefully pulled the ends apart. One was hard to get apart to I had to push it with the tip of a knife. Once the old was off the new was super easy to put back on. Side the tips to the clips, screw the plate in place and push the oven back in place. Flip your fuses and turn on the oven. Yeah!

Turn off power to oven. Removed the rack. used a 1/4" nut driver and removed the two screws holding the element to back of oven. Slid the element out, unhook the two wires clipped to the end of the element. Replaced it with the new element, installing it in reverse. Took about 15 min. Rememer to turn off power to oven before attempting to work on it.

Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed the 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy

Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."

This part is a PC Board. Step 1 - pull the oven away from the wall far enough to permit access to the back. Step 2 - Unplug the oven. Be careful of the gas supply line. Step 3 - Before touching the new part, wear a "grounding strap." Step 4 - Using a "Phillips" screwdriver remove the four screws that connect the top cover plate that covers the control assembly. Once the screws are removed the top of the cover will need to be rotated a bit to the rear to remove it from the oven. Step 5 - Carefully remove the ribbon wire by gently grasping the locking bar tabs with a thumb and forefinger and pulling back until the ribbon wire slides out. DO NOT use any force here. Gently move the ribbon wire out of the way being careful to make no crimps in it. Step 6 - Using a magnetized "Phillips" screwdriver remove the four screws holding the oven control assembly to the oven. Carefully remove the foam insulator connected to the bottom two screws. Step 7 - Locate the new oven control assembly above the old assembly and begin transferring the wires, one at a time. Care here is needed as the connectors are tight. Grasp the connector with your fingers and pull straight back. DO NOT pull the wire. Step 8 - Once all wires are transferred dispose of the old oven control assemble and screw the new assembly back on to the stove. Use a magnetized "Phillips" screwdriver. Insure the foam insulator is attached to the bottom two screws in the appropriate holes. Step 9 - Once the oven control panel is secured, insert the ribbon wire carefully and close the locking tab. Step 10 - Install the top cover. Make sure the bottom lip is under the foam insulator and that all wires are clear and free before pushing it tight to the stove. Replace the fastening screws. Step 11 - plug-in the stove and insure all oven functions work correctly. Push the stove back into place.

The repair was somewhat easy. The replacement elements are pushon type. The only thing is that the G.E. Hotpoint wire on the right side of the bake element is short. Be extra careful to not have it go back into the back oven wall or you will have to take the back cover plate (Pull out the range, remove the back cover using a nut driver or a magnetic tip srewdriver with the bit removed works[Wires are right there]. This is as easy a job as can be.