JBS26 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- charles from ft.pierce, FL
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rusted out burnner bolws
Remove old burnner bolws and install new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Las Vegas, NV
- Parts Used:
- WB27T10469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no display
Turned off circuit breaker to stove, remove top panel and then the old control module and installed replacement. Power back on and top panel reinstalled. Easy!!! And Everything works like new!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Bainbridge, NY
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dirty bowls
used my hands to remove heating element, then remove drip bowls, then install new bowls, then install heating elements, done!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Wheat Ridge, CO
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burner Terminal had shorted out out.
had to pull range away from wall and unplug it so we could get behind to access the rear panel. we then removed old terminal block, by, removing screws from back panel, and one screw from under burner drip pan, inserted, new block, and reassembled. plugged it in to test and burner worked properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Richmond, TX
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
GE Electric Range rear left burner quit coming on
Removed the back top cover with 1/4" nutdriver. Removed the burner terminal block with 1/4" nutdriver. Within 15 minutes had the terminal block kit removed and installed and in service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from Dallas, TX
- Parts Used:
- WB31T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace drip bowls
Husband just snapped in place in about 8 seconds! Thanks for the fast delivery and pleasant staff assistant.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Centereach, NY
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new drip bowls for stovetop GE
removed the burners and dropped the drip bowls in. Very easy to do,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Mayview, MO
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bakelite block in the terminal block broke in two.
I can add nothing to the video you furnished on your website. I am generally all thumbs with home repairs - especially anything electrical - but, your video led me right through it. A good experience. We'll do business again.Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria T from Germantown, MD
- Parts Used:
- WB31T10010, WB30K10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burned heating coil
Just pulled old coil out of the plug. Replaced drip bowl and inserted new coil in. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from De Leon, TX
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Front and back burners not getting hot
Followed the video supplied with the email on the parts order form. Biggest problem was pulling the range out from the wall, the repairs went without a hitch. The PartsSelect video was a great help showing the short cut to getting the new wires in by using the old wires as a pull wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline A from West palm beach, FL
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Corroded connectors and melted block on an electric stove.
The original GE blocks/wires were color coded to specific burners. The new ones are not color coded since they are sold individually and work with any burner, but they were identical to the originals in every other way. Just remove old blocks one at a time and connect the replacement so that the burner is connected to the proper control. Since the stove age was unknown, I replaced all four blocks to eliminate a repeat of the problem later. The screws holding the blocks and the wiring cover on the stove back require the same small socket wrench; not enough room in some places for an adjustable wrench. It took no more than 20 minutes to replace all four, test the burners, and close up the back wiring panel. The instructional video on the website eliminated my hesitation to tackle this repair. The parts arrived the next day, with no special shipping service requested. WOW. PartSelect will be the first place I go to find what I need for the next fix-it. I'm almost looking forward to something else breaking. LOL. Thanks, PS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Aurora, CO
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Old Surface Burner Block Kit Disintegrated
Very easy. Followed the video instructions. Unplug stove. Cut old wires. Tape new wires to old wires to facilitate pulling new wires thru old hole to back of range. Removed back cover. Pulled old/new wires thru to back. Removed old connectors. Attached new connectors. Replaced back cover. Screwed new terminal block to front of range at burner. Attached new burner. Plugged in stove. Replaced stove in counter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Fort Oglethorpe, GA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The burner would not work.
I pulled the range out, unplugged it, took the back off, unplugged the old terminal block and removed it. Attached the new block and ran the wires through to the back and plugged them in. Reattached the cover on the back of the range, plugged the range back in and pushed it back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ervin from Dublin, GA
- Parts Used:
- WB2X8228
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Two surface burners did not work
Removed the two screws from the range's top and the rear zinc cover and replaced the two front clip receptacles. It took me 30 min to finish the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammed from San Jose, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
none to occasional power to burner elements
Exactly followed the instructional video and my installation was flawless. Now the burners power up and function like new. The whole repair was smooth and easy.
Was this instruction helpful to you?
Thank you for voting!