JBV42G0H2 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Floyd from Warren, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mirtes from Marlborough, MA
- Parts Used:
- WB17X5113
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heating element not heating
Removed the terminal block. Cut the wires. Cut the sheathing to expose the wire. Connected the new wires with the old wires by twisting them together. Added the wire nut and reconnected the block. Tested ok.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jilan from South Milwaukee, WI
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scorched Element
It wasn't so much the repair that was needed as how impressed I was with the fast delivery. Without a fourth burner & a holiday weekend coming up I was in desperate need of my element. I ordered it around 1:00 pm on a friday & it was delivered the next day before noon! Very impressed with the ease of ordering & receiving. Thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Fort Bragg, CA
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
element burnt out
changed element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Copperas Cove, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No Problems
I removes the old element and drip bowl, then replaced the drip bowl, then replaced with the new element. Approximatly 3 minutes. . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Scituate, MA
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burned out surface element
This is an easy repair and for anyone thinking that they might have trouble effecting it, you all have my assurance that all the heat related elements are easily replaced. These elements are basically plug in and there is a shielded area (usually placed in the northeast quadrant of the burner unit. With everything turned off, pull the burnt out surface element up and toward the southwest. It should unplug from the female receptacle. Installing a new element involves performing this in reverse by coming into the surface with the prongs facing downward towards the receptacle and then pushing towards the northeast and downward at the same time The element should click into place. The entire time necessary to effect this repair should be less than ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Cerritos, CA
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stove Burners did not work.
The repair is simple, pull out the old, plug in the new. The most difficult aspect of the repair is to make sure that you have the right part. As this is an old stove, and it was a builder model, the model number did not match exactly, and I got the wrong part which I had to return. Look at the pictures carefully as many of the parts look similar.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from cincinnati, OH
- Parts Used:
- WB1X5508
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
broken nylon retention pin in upper oven door
Removed 3 lower screws holding the upper oven inside door panel to the door frame. There is enough flexibility in the panel to coax it away from the frame at least an inch. Removed the old nut plate from inside the door and replaced it with the new one. Screwed in the retention pin and 2 washers while holding the nut in place. Assembled the 3 lower screws to complete the assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DeeAnn from Clinton, MO
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob had broken off
My husband was able to easily remove and replace the switch and know with-in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from South Daytona, FL
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed to replace the 6" surface unit.
My GE range is 20 years old, and still going strong. All I needed was to replace the 6" surface unit. After making slight adjustments, it was just a matter of placing the new unit. After finding this Co. on the internet, and checking others, I will certainly order from Part Select again!Dorothy Trakshel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Wilmington, DE
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
older element losing heat
really easy, remove old and replace with new...easy, once you have ordered and received the correct part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from San Andreas, CA
- Parts Used:
- WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original trim ring did not fit
I had an appliance guy replace a burner(Calrod unit)on my 47 year-old GE range, but he didn't tell me that the original trim ring wouldn't fit. I decided to look up on PartSelect to see if I could get one to fit the new burner, and I did! Fits perfectly......no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Merritt Island, FL
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I could not find a dealer who could tell me what part I needed because the model was discontinued
I just went to your web page and indicated I needed an 8' surface element and up popped a picture; I ordered it and plugged it in and it works perfectly. I didn't need a model number, or a part number. Three cheers for a simple solution and a 1st class web page!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from wernersville, PA
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken heat element
Fit was perfect, slip right in prlace and works great thank u! R.e.Rice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudine from The Colony, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
surface element not working
I simply pulled the old surface burner out, and plugged the new one in. It took less than one minute! The amazing part of this repair, is actually that PartSelect sent the replacement surface element burner OVERNIGHT! I could not believe it, and was VERY impressed with their commitment to help their customers in time of crisis. It arrived just on time for my Thanksgiving not to become a nightmare. Thank you PartSeclect!
Was this instruction helpful to you?
Thank you for voting!