JGSP28BEK5BB General Electric Range - Instructions

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

This temperature sensor is very easy to replace. There are two screws inside the oven in the top middle of the back of the oven. Take these off. on the back of the stove there is a metal plate with 5 screws I believe. Take these off with a nut driver. Then you will see a white connector coming from the spot where you took the other screws off. Take the white connector apart and pull out the temperature sensor from the inside of the oven. Then put the new one in.

I pulled out the drawer and inserted the new support. This one inserts into the back of the drawer as opposed to the sides. I had ordered two of the replacements even though I only needed one and decided to replace both. I think it was a good move as the drawer works better than when we first got it. Just one simple screw made it complete.

I picked the least expensive and most likely issue with our oven that was not indicating a correct oven temperature. I am sure with a 15+ year appliance that the circuitry is on its way out but wanted to give this a try to avoid a new appliance purchase. Oven pre-heat setting takes much longer to finish with the age of the oven. However, after the new sensor the oven will maintain a more even temperature for the cycle.

Removal of the sensor from the inside of the oven is a bit awkward since it is located between the broiler elements at the back but a nut driver was the correct tool and worked fine. A bit stuck with the heating of the connection but pretty simple to replace. Must remove the back first to uncouple the connector. Simplest part of the repair.

At best a temporary fix for a an appliance this old.

Very easy to remove the parts and to reassemble

I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on them, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!

Replaced old with new.

Order parts and installed - no tools needed - completed repairs less than 1 minute

Unplug the range from its wall socket to avoid electric shock. The various range parts that support a pot or frypan are easily lifted off their perches, exposing the small white igniter. The only moderately difficult aspect is wiggling the igniter out of its retainer. The electric wire leading into it then can be pulled out and fed into the new igniter with a push. Replace igniter in its retainer, then replace the range parts you removed to expose the igniter and plug the range back into the wall socket. Piece of cake.

Took the oven door off and removed the inner door panel, put new glass assembly part in and reassembled. The hard part was getting the door hinges locked back into place.

Turn gas off. Remove front door by pulling the lock covers back and pulling door up. Remove all cooking racks. Push back and lift enamel cover plate. Remove heat shield. Either use crosstip screwdriver or nutdriver (ratchet driver works as well, all the ovens have a different size nut/screw so check your size) and remove ignitor. Remove small shield and gas burner tube from pan. Remove all nut/screws from pan, lift up and pull towards front (ignitor can not go through pan) exposing electrical connector behind insulation. Disconnect and pull through pan. Replace pan (I had to replace older pan due to rust) and push connector from new ignitor through hole and connect to plug. Push pan in attach new ignitor (easier) to gas tube burner and place burner back through hole. Reattach shield and burner to tube to pan. At this point I tested the new ignitor which worked perfectly. Turn off oven. Place heat shield over burner tube. Replace enamal cover plate. Replace oven racks. Place door and lock holders on the hinges. Easy. BTW I am 70 and it took me just at 25 minutes with set up for tools, door, rack and enamel cover removal, heat shield removal and then the more labor intensive nut/screw removal, old ignitor and gas burner tube removal, pan removal, new ignitor replacement, new pan replacement, gas tube with shield attachment, heat shield attachment, enamel cover, grill racks and door attachment. Perfect parts fit well work well.

slid the old ones out and slid the new ones in. done

Replaced gas control valve problem solved, all went well

Performed repair using a video for reference.

recieved part the next day. looked different but I followed instructions and the part worked perfect.