JB900TK5WW General Electric Range - Instructions

My friend's husband came over to help. I mentioned that after unscrewing the old bake assembly unit, we would have to capture the wires or they would slip into the back. Before he even had the screws undone, the wires did, indeed, slip into the back. He then removed the back panel and retrieved the wires, pushed them back through the insulation and clipped each of them onto the back assembly. However, the wire clips kept slipping off so he eventually had to criimp the clips to keep them tight on the ends of the bake assembly. That troubled me; what if in the future one of those clips comes loose while the oven is in use? Any suggestions on how to keep these connectors on tightly?

The cooktop is just set in the counter with no fasteners. I shut off the power and lifted the unit out. Ten small screws held the top to the body. After removal, I took a picture to have a wiring reference. I disconnected five wires with push-on terminals, then removed two Tinnerman nuts with needle-nose pliers. The failed burner was free to remove. There were two mounting ears on the bottom of the burner at positions 12 and 48 as stamped on the bottom. I transferred the mounting ears to the new burner, one screw each. I then positioned the new burner and secured with the two Tinnerman nuts, replaced the five wires, screwed the top back on and slipped the unit into the counter. Done.

I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.

Removed old switch, put metal jumper from old switch to new one and connected wires to the new one . Reinstalled. Works great.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Remove the top back panel to expose the switch. Remove the switch knob & mounting bezel and then unscrew the 2 mounting screws from the front. Replace the wires one by one and follow the enclosed directions in the event that this is an upgrade for an older switch. Remount the switch from the front and replace the back panel.

Turned off power. Opened range door, removed 2 screws that held top in place. Took a photo of the existing wiring for reference. Removed old burner. Be careful with spacers & springs. If dropped, they will be hard to locate in the insulation. Replaced wiring connectors & verified proper location with photo. Closed cover, replaced 2 screws & turned on circuit breaker.

Had to remove rear cover to connect wires, removing them from the front caused the wires to fall into rear.

1.Move range in position to access electrical wall disconnect and unplug. 2.Remove two 5/16 screws (located under top fwd. edge of cook top, Lift entire top assy up from front and prop with appropriate device(short 2x4 about18 inches long works well) 3.Remove two small phillips screws securing two metallic keeper devices holding burner assy in place. This should allow burner assy to be removed.4.Disconnect electrical spade connectors from ceramic terminal blocks on old burner assy.CAUTION: [SPADE CONNECTORS FIT TIGHTLY DO NOT PULL ON WIRES USE PRYING FORCE WITH FLAT SCREWDRIVER DIRECTLY ON TERMINAL].Remove connectors one at a time re-connecting to same location on new assy. Reassemble in reverse order.

unscrew and disconnect the old unit. Connect and screw in the new unit

Really easy. Part came in rapid time and was the right part. Went on web and got instructions with video how to install.

We ordered the part from PartSelect and received it the next day. Didn't even have to move the range out from the wall. Just unscrewed the two screws on the back wall of the stove that hold the bake element in place with a socket wrench, then pulled the old bake element and wires out about 2-3 inches so we could disconnect the old bake unit. The element was kind of hard to pull out, but after you pull it from the wires, just plug in the new bake unit, push the wires back in and put the screws back in. Oven was up and working again!

I didn't know anything about this repair, other than I was replacing a part, so it never occurred to me that I needed to make sure there was no power to the oven. When I pulled the element out, there was a large spark. I flipped the breaker off, then finished the R&R.

Make sure you turn power off at the breaker, then replace the element.

Tim

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

1.Disconnect the power cord. 2.Remove two screws pull the element out. 3.Disconnect the wires attach to element. 4. Install the new element connecting the wires. 5. Align element with holes and tighten screws. 6. Plug in power cord and begin to cook.