J486A3 General Electric Range - Instructions

I removed the unit easily with anut driver, however the unit also supported the thermo-link. I had to use the hack saw to relieve a small opening for the thermo-link to pass through. No real problem. Then a few holes to be drilled to attach the 'link' to the base of the broiler unit.

BUT-I went into the website listed on the box. GEAppliances.com Guess what? Their price was twice yours!!

First I made sure the electricity was off. Then, I flipped the burner up, and loosened the screwon the hinge. This allowed the burner to extend onto the cook surface. After loosening the clips holding the ceramic insulator together, the wires to the element were exposed. The wires were then transferred to the new burner element from their corresponding position on the old one. The new ceramic insulator was affixed over the wire with clips, and the hinge reattached. The chrome ring was worked over the burner, and the burner reseated in its proper cook poistion. Testing confirmed the burner to now work as new.

Turn off electricity to the oven. A socket set was needed for the small screws in my old oven. Once the screws were removed the element came off easily from two wires in the oven. You have to be careful when handling the wires that they don’t fall back into the oven. The new part was attached to the two wires, screws were tightened on the new element and that was it. When the oven was turned on the new element smoked a little but I saw on the video that is normal.

First I shut off the circuit breaker for the oven then removed the screws that hold the element in place. The element was pulled out about 3 inches and unscrewed the 2 screws to disconnect the two wires. Upon receipt of the new element, I simply reversed the above process and the oven performed like new. Very easy, very quick and very grateful to have the oven operating again and it was a very inexpensive fix.

Replacing the part was fairly simple. Do not forget to dis-connect the element from the back.

The customer service at PartSelect.com is wonderful. They assisted me to located a part for a 40 year old oven. Took only a few minutes to take the old one out and put the new one in. Process was pretty self explanitory.

removed 2 nuts holding the element in the oven. removed 2 screws that secured the wires to the element. installed the new element in reverse.

turn off breaker in electrical panel....remove stove socket from outlet....remove rear panel from stove....undo wire connectios from broiler element....inside the oven, gently move thermostat wire out of the way....unbolt broiler plate from rear wall....remove broiler hanger and then broiler element....reverse procedure and you're all set.

Unplugged Stove, pulled away from wall. With smaller wrenches, took the two screw-nuts off the inside back and above that hold the broiler element in place. Since it is an older stove...took the back panel off the stove with philips screw-driver which consisted of 10 screws. Once that was removed was able to unscrew the broiler element from the two wires that provide the electricity. Used the flash light when I had to unfasten the screw-nuts inside the stove because kitchen lighting wasn't strong enough.

Turned power off to oven. Unscrewed back plate exposing wires connected to heating element. It was difficult to unscrew the connections between them as it was hard to reach in because the oven door was in the way, but i finally succeeded. Unscrewed the bracket holding the burned out element and then attached the wires to the new element. Attached the bracket and I turned on the power. I then tested the oven and it worked.

The removal- replacement problem basically involves the shortness of the connector wires to the terminals. Because the burner is close to the top there is little room to use a screwdriver. The old unit used metal screws. The new came with open threaded holes in the terminals with two threaded screws. Used a small 1/4" ratchet which worked OK, but had to carefully bend the ends of the terminals to allow me to lower the element to an angle that would all room for ratchet action. (All design engineers should first have to work in maintenance before going to drawing board!)

S. Cooke, Houston Texas

Replaced damaged element exercising the care suggested in repair comments by previous customers. Old unit had screws connecting the broiler element to the stove's electrical supply wires, which were difficult to remove due to old age. Just took a little extra care to ensure that supply wires were not damaged during disconnect and after reconnecting the new element the broiler tested OK. It is once again broiling steak to perfection

I shut down the electric to the oven at the circuit breaker. Then i loosened the mounting screws and pulled the element from the back wall of oven. Then i disconnected the two leads to the element with a phillips screwdriver and removed element. Installation was done in reverse order.

After receiving parts, was getting rims unpackaged and removing the old rims, then and installing the new ones. Extremely easy to do. No tools needed

Removed 4 screws and removed the old element and replaced in the reverse order.