JKC26004 General Electric Range - Instructions

Could not believe how fast the part shipped. 2 days and it was here. All it took was using a nut driver to remove 4 screws and then put the new one in.

Unplugged range. Removed old element from back of oven which was held in by two screws. Unscrewed the wires that were attached to old element and screwed them into the new one.

The hardest part was working in the oven.

Turn off power
Open Oven Door, remove racks
Remove two mounting screws with nut driver.
Slide the element out to expose the wire connections.
Remove the screws and pull the element out.
Place the new element in oven.
Clamp on to each of the terminals with vice grips to keep from bending the element and install the screws.
Slide the element back into place and put the two mounting screws back in.

Put the racks back in and turn on the power and test. You may get a little smoke off the new coil.

Like I said the hardest part is leaning into the oven to attach the screws, do not sit on the oven door.

No. 1 thing I did is I unplugged power supply to oven, second- unscrewed two screws that was holding cover plate and removed cover plate with a set of pliers, pulled element out and unscrewed two screw with power wires and installed new element, tightened screws and re-installed cover plate, tested oven turning on oven and in a few seconds element got hot, job done!

First I turned off the breaker to the oven,
then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I placed the new element in the oven, reconnected the wiring and replaced the two screws in the mounting bracket. I reset the breaker and turned the oven on to about 450 degrees for 30 minutes to burn off the new smell of the element. This job was very easy and I saved about $100 from paying a service to do it.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.

I was very pleased with all the follow up from the time of order until the arrival of the heating element. I have never had the personal communication as I did with your company. The part was ordered on Dec. 26th and arrived on Dec. 29th. Due to the holiday schedule, I did not expect arrival until weeks end. My neighbor installed the heating unit for me and it is doing just fine.

Thank you for the excellent service.

Sherry Shelton

First we unplugged stove, if wired into circuit shut off in breaker box. Undo four screws on back cover and detach wires from element. Remove oven door by pulling open and sliding it up off hinges. Undo two screws holding element to back wall of oven. Slide in new element and replace screws in back wall. Replace door. Slide wire leads on new element in back, at this point we plugged range in and tested element to see if heating. It worked so we replaced cover, slide range in and leveled it with wedges. Time for pizza.

The repair is simple. Unplug or turn off power to stove. Remove the 2 visible screw where the element connects to the back of the oven. Pull the element with back plate out. The back plate is part of the element. Remove 2 screws that connect wire. Mark which color connects to which lead. Re-assemble in reverse order. Takes about 15 minutes,

My daughter and I turned off the breaker to the range and removed the old element and replaced it with the new one. My husband came home and took over after we had done almost everything ourselves!!

It only took 15 minutes and a nut driver to replace.The part was $22,well worth keeping my oven going for a few more yaers

Unplugged unit.
Removed two screws with nut driver.
Bake element easily disconnected.
Ordered part Tuesday night.
Received e-mail that part was shipped Wednesday.
Part arrived Thursday.
I installed part in minutes. Stove working again.
Anyone could do it.

I ordered the part on Sunday afternoon and it was delivered by noon on Tuesday. I couldn't be more pleased. The service was amazing and the price including shipping was very fair.
I need wheels for the rack in my dishwasher and I plan to order from partselect.com.
With the service I received, I'd recommend Parts Select to my family and friends.

Parts arrived quickly and install was easy as removing two screws and removing the broken burner. Installed the new and I was done!

Super simple installation. Once power was isolated from the oven, we removed the old bake element which had four nuts/screws. Then we installed the new element, turned the power back on and tested the oven. It worked perfectly! The whole process took maybe 5 minutes.