J350*03 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from Portsmouth, RI
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
burner warped, pan didn't sit right
It would have been easy, but the screws that came with the replacement burner were too long for the ceramic insulator to fit over. Had to grind down the screws fro 3/8" long to 1/4" long. After that, piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deon from Olympia, WA
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Element burnt out
The repair was easy once he read the directions. The part arrived about 4 days earlier than expected. Great company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from Carmel, CA
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
broiler element was broken
Asked a local repairman to fix it. I saved money(saved $20.00) by ordering the broiler element from GE part select via customer service agent. The agent was informative and helpful. The part arrived the next day even with regular shipping cost. Impressed with the GE part select. Will use the company again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Plano, TX
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers
broil element failure
Unscrew 4 easy nuts and 1 most difficult nut, gently pull both long and short wires, at this point assure the wife that you did turn off the power.You may wish to attach a cord to short wire as it wants to vanish into the rear bowels of the oven On instruction of the wife clean the oven. Reverse dismantling procedure. Switch oven on. Bask in wives praise.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Novi, MI
- Parts Used:
- WB44X173
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Our broiler element wasn't working.
We unscrewed the element easily enough, but had a hard time disconnecting the prongs. Once we did, we had to use a thin screwdriver to open the clamps to fit the new prongs into them. After all was accomplished and we switched on the breaker the broiler still didn't work. Either we did something wrong or the element wasn't the problem. We haven't decided our next move yet; whether to get a repairman in or buy a new oven. It's a pretty old oven/range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from New smyrna beach, FL
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Burner constantly heated
Good directions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Baden, PA
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Front Burner,no control of.
The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Hamilton, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Shaft for burner control knob broke off
I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?
Was this instruction helpful to you?
Thank you for voting!