J350*03 General Electric Range - Instructions

Turned off the breaker to the range. Turned on range to ensure no electricity was currently flowing to the range. Turned the range off and unscrewed the tilt lock hinge. Pulled the burner out to expose the wires. Popped the snap locks off the cover box and unscrewed the wires connected to the posts. Followed recommend directions to expose approx. 1/2" of new wire (this is what I used the knife for since I did not have a wire stripper available). Slightly cut thumb in the process (no blood, though). Removed old burner. Put new burner in place, re-attached wires to the posts and screwed in to place. Placed cover box back in place and secured using new snap locks. Attached tilt lock hinge using new screw that was provided. Turned breaker back on and turned on range. new burner worked great. Took about 20 minutes total. Wife was extremely impressed, mostly that I didn't electrocute myself. She now wants me to replace other three burners. No good deed goes unpunished.

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

First I turned the power to the stove off at the breaker box. Next I removed the two screws holding the old element in place against the back wall of the oven. I gently pulled the element forward. I wound a couple lengths of spare colored wire around the two electrical wires before disconnecting the retainer screws at their connection points. This insured that the electric wires would not fall back inside and behind the firewall. I then disconnected the screws holding the electrical wires to the broiler element. I removed the element from the oven and discarded it. I then connected the screws through wires and the connecting points of the new element. I removed the spare wires hold the electrical wires. I positioned the broiler element in place and screwed in the retainer screws securing it in place. I turned the breaker switch to the "on" position and tested the new broiler element. It tested fine. Job done in 15 to 20 minutes. An able bodied person could do it in less than 10 I'm sure.

removed timer assy. with wires attached, then mounted new timer in place. Took wires off old timer and installed on new timer one at a time. Worked like a charm. Also very pleased with the speedy service you provided. Yours Truly Ron Ferro

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

Some times it's not the element at all, as in this case. After rmoving the element I found the wires broke. Fortunatly I had some high temp wire left over from a earlier oven repair. I used butt splices and heat shrink tubing to repair the wires. Then I crimped on a couple of eyelets and fastened things dow.n I received a big kiss form the wife for getting the broiler fixed so fast. Maybe a little extra work, but the rewards were worth it.

Unscrew 4 easy nuts and 1 most difficult nut, gently pull both long and short wires, at this point assure the wife that you did turn off the power.You may wish to attach a cord to short wire as it wants to vanish into the rear bowels of the oven On instruction of the wife clean the oven. Reverse dismantling procedure. Switch oven on. Bask in wives praise.

Good directions

Asked a local repairman to fix it. I saved money(saved $20.00) by ordering the broiler element from GE part select via customer service agent. The agent was informative and helpful. The part arrived the next day even with regular shipping cost. Impressed with the GE part select. Will use the company again.

Repair is pretty easy, its the accessability that makes it difficult. This is a wall mount oven. Removing the door would provide pretty good access, but having to reach over the door into the very top back of the oven is a real pain (in the back and other places). As another customer said, there were many dropped screws and much cussing. The old element terminals were just holes in a metal tab that accepted tapered screws. The new element had terminals that were threaded to accept the screws provided. It took lots of twisting and turning of the element and the power wiring to get the terminal on the wire lined up with the terminal on the element in a position where I could hold them together and insert the screw and start the threads. Don't try this after you've had a beer or two. Whew!!! Many tries, sore back, but did it. Like I said, simple except for the reach. Bake element was much easier. Hope I don't have to do this one again. My GE oven is a winner (20 plus years old) and Parts Select has what you need at a reasonable price and ships quickly. Have used before and will use again, if needed.

The repair was easy once he read the directions. The part arrived about 4 days earlier than expected. Great company.

Replaced the old with the new following directions (mostly).

This was a second hand stove we have had for about 3-yrs. I noticed immediatley that the drip bowls and rings were not OEM parts & the bottom of the burners had actually been bent to fit the rings. I was very glad to find this website with a detailed diagram of the stove and parts. I intend to replace all the burners, drip bowl & rings, and then start replacing other parts as needed.

From inside the oven after turning off the breaker I removed all of the mounting screws with a nutdriver, I removed the wire screws after taping all of the wires together with a small piece of tape to prevent them from falling back into the opening. I installed the wires with the original screws as the provided screws would not fit the holes, tightened them, removed the tape and placed the element back into the opening. I then tightened the hanging brackets, after getting them to align and then tightened the rear mounting bracket. It did help to adjust the baking rack down and leave the baking rack in place to have a place to rest my arms. The install then became a piece of cake!

My husband was able to easily remove and replace the switch and know with-in 15 minutes.