J797D2 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Karl from Kempner, TX
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls could not be cleaned
Replaced drip bowls.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from Houston, TX
- Parts Used:
- WB44X173
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Old Broiler Ekement burned out
The removal- replacement problem basically involves the shortness of the connector wires to the terminals. Because the burner is close to the top there is little room to use a screwdriver. The old unit used metal screws. The new came with open threaded holes in the terminals with two threaded screws. Used a small 1/4" ratchet which worked OK, but had to carefully bend the ends of the terminals to allow me to lower the element to an angle that would all room for ratchet action. (All design engineers should first have to work in maintenance before going to drawing board!)
S. Cooke, Houston Texas
S. Cooke, Houston Texas
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joan from coram, NY
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
broiler element wa burned out
I shut down the electric to the oven at the circuit breaker. Then i loosened the mounting screws and pulled the element from the back wall of oven. Then i disconnected the two leads to the element with a phillips screwdriver and removed element. Installation was done in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from peabody, MA
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
replacing old rusted drip pans w/ rings
simply lifted the heat coil and slid the rings off and lifted the drip pans off. Vacumed the bottom underneath the old pans. Cleaned the grease off around the stove where the rings sat. Let it dry and added the new rings and pans. Looks like it did 30 years ago.......let them try making a stove last that long today !! Make sure the power is OFF at the electrical box.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larry from fort wayne, IN
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
original trim rings
replace trim rings with the new shiny ones I got from parts select. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Lecanto,, FL
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broiler Element burned out.
The replacement was straightforward, six screws. Instructions were provided with the part along with the necessary screws to fit the new element terminals.
Open the breaker, verify power is off, remove the old burner. Install the new burner and mounting bracket. Restore power and test. In and out in less then thirty minutes.
Open the breaker, verify power is off, remove the old burner. Install the new burner and mounting bracket. Restore power and test. In and out in less then thirty minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRIAN from WEST POINT, UT
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
broil element had a "burn through", w/n turn on
less than 15 minutes R2 the part, ops ck'd good. 4ea 1/4" screw/nuts, they didn't fight me...
Was this instruction helpful to you?
Thank you for voting!
Old and corrosive due to age
After receiving parts, was getting rims unpackaged and removing the old rims, then and installing the new ones. Extremely easy to do. No tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from West Melburn, FL
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original parts lost or discarded by prvious owner
Just replaced drip pans and rings on stove
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan D. from Holland, MA
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The broiler element had been broken for some time.
The stove was new when we moved into our new home but opted to leave "our" stove in the basement until the one that came with the house had seen it's better days. The removal of the original element required the use an allen type of driver - it's removal was simple and the new element popped-into place without a problem and I refastened with the screws that came with the new element. The part arrived from PartSelect right on time, in good condition, and I would definitely do business with PartSelect again when I need to! My only complaint has nothing to do with PartSelect, it is the angle one must assume to refasten the part into place! Thank you, and I'll be back!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Kalama, WA
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Blown Broiler Element
Removed 3 screws from cover {center of back side of oven}, removed 2 screws from wires connected to element, then removed 2 screws mounting element
{inside oven}, pulled it & replaced it.
{inside oven}, pulled it & replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Chapel Hill, NC
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace Broiler Element
After an exhaustive search of local oven dealers and big box stores, I could not find a broiler element for my aged GE stove. I did find it online at Parts Select for about 1/3 the cost from GE online parts.
Replacement was easy-- just as described in posts for this part. The 'hardest' job was getting the screws started that hold the wires to the element-- small screws and small holes-- but just required some patience. A simple, inexpensive repair that avoided my having to replace the entire stove. Thanks!
Replacement was easy-- just as described in posts for this part. The 'hardest' job was getting the screws started that hold the wires to the element-- small screws and small holes-- but just required some patience. A simple, inexpensive repair that avoided my having to replace the entire stove. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Brookhaven, PA
- Parts Used:
- WB32X10013, WB32X10012, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burners were burnt
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- margaret from lantana, FL
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
both oven and broiler coils were burnt out
extremelyquick delivery on standard mail and so easy to install and really the lowest price. so happywith this company
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Tulsa, OK
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
top element in oven was broken ,not working
Removed 4 screws and removed the old element and replaced in the reverse order.
Was this instruction helpful to you?
Thank you for voting!