JBC17G2R2 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from SONORA, CA
- Parts Used:
- WB3X5699
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
missing knobs on clock and timers
Installed new knobs, mom is happy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Sinking Spring, PA
- Parts Used:
- WB2X1452
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Still need an other nut to keep broiler support inplcae. Support bar did not come with new screws so I must locate one new one.
I took out the old broiler support bar, but it was being held by one screw. I did install the new bar with one screw, but I need to obtain a second screw. I still have not located a second screw, but it is inplace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wayne from GARLAND, TX
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
broil element burn into
turn off electricity to stove and simply remove the screws from the heating element and put new element back in place .put screws in and turn power back on and test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lafayette, CO
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
broiler element circuit broke
First removed oven door, according to Reader's Digest repair manual, then removed two screws holding element. Pulled element out several inches, then removed one side of bracket holding up front of element so that bad element could be pulled further out. Then disconnected two red wires from one side and two light blue wires from other side. Removed old Element. Attached two light blue wires to one side and two red wires to other pole, inserted element back into rear wall and attached with two screws, Re-attached bracket holding up front of element. Re-installed door. Tested and it worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from CALDWELL, ID
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element did not work
Got new part! Unplug range!!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Southern Pines, NC
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Surface element was corroded.
Removed existing surface element and replaced with new element.
P.S.
Part Select service was excellent.
P.S.
Part Select service was excellent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Buffalo, NY
- Parts Used:
- WB31K10266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace a drip pan
OK, I put the drip pan under the burner. Without a single problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Cleveland, OH
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
melted electric range element
Because of the superb pics and descriptions on the Part Select site, I was able (with NO range model number) to order the correct range element for beloved son's stove. He plugged it in in 3 seconds, works great !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christy from Danville, CA
- Parts Used:
- WB3X5699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
timer knobs broken off
I simply took the 3 new timer knobs and slid them on the metal shafts. It took less than 5 minutes to replace all 3 knobs. Now I can set the start, stop and time functions which have been inoperable for over 5 years. An easy and straight forward .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DeNise from FT WASHINGTON, MD
- Parts Used:
- WB3X5699
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Knobs were broken.
Removed old knobs and inserted new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emma from The VIllags, FL
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old unit failing to heat all coils
I first removed the unit by pulling gently from connection. Replaced the new one in that same manner - simply inserting into connection.
Very easy, I'll probably try it again soon.
Very easy, I'll probably try it again soon.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Hindman, KY
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner wouldn't operate
Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel
Knott County Housing Authority Maintenance Personnel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from SAN JOSE, CA
- Parts Used:
- WB17X5113
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
terminal block not working
simple remove the old one, strip old wires to make longer, twist wires together, put on wire nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Charlotte, NC
- Parts Used:
- WB44X173
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Broiler unit burned out
I removed the unit easily with anut driver, however the unit also supported the thermo-link. I had to use the hack saw to relieve a small opening for the thermo-link to pass through. No real problem. Then a few holes to be drilled to attach the 'link' to the base of the broiler unit.
BUT-I went into the website listed on the box. GEAppliances.com Guess what? Their price was twice yours!!
BUT-I went into the website listed on the box. GEAppliances.com Guess what? Their price was twice yours!!
Was this instruction helpful to you?
Thank you for voting!