JBC16G0F2 General Electric Range - Instructions

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

shut off electricity to the range, removed the screws holding the element in place, pulled the element out as far as it would go, removed the screws holding the wires in place, tossed the old element, attached the wires to the new element, pushed the element back into place and reattached the screws holding the element in place. Turned the electricity back on and the oven heated right up.

Also, the part arrived the day after I ordered it. Great Price & Great Service.

I removed the screw holding the tilt-lock hinge, then removed the insulator brackets and unscrewed the wire terminals. Units come with new insulators, brackets, terminal screws & hinge screw. This is a very straightforward operation.

Disconnect power. . . Remove control panel, pull wire connectors,[note location] remove old switch, install new, install wires, snip stem to length, set knob . . . Turn on power - works. [Note this is a live part even when not connected]

Replaced all the ordered parts, and straightened a bent "rest piece" (one of three) on the element os the large burner, which made it rest perfectly on the new Trim Ring. It doesn't easily fall down into the bowl now while I am using the burner. The new Bowls look so nice, and the stove looks nearly new!

I now know where to go for help when I need to repair appliances. You seem to have everything that could possibly be needed. Thank you!

pushed on the new knobs.
thanks fore having the parts.

Easiest thing I've done. Shut off breaker. Unplug range. Pull out from wall (because this is a good time to remove the back, clean under and around the unit, check out the insulation and electrical contacts....or skip it, whatever). Open oven. Remove door (while ajar, pull up). Remove racks. Unscrew mounting plate from back interior wall. Set screws aside. Gently pull element forward until the leads and wires come through the insulation. Remove any strands of insulation that stuck to the leads and connectors. Unscrew leads. Keep left wire to the left and right wire to the right. DO NOT CROSS. Set screws aside. Discard old element. (This is a good time to clean your oven, if you haven't in a while.) If you cleaned oven, wait until dry. Position new element, feet down, in bottom of oven. Position left wire on left connector. Screw tightly BUT DO NOT BEND LEAD. IF YOU BEND IT, THEN DO NOT BEND IT BACK. CALL A PROFESSIONAL. Position right wire on right connector. Screw tightly BUT DO NOT BEND. IF YOU BEND IT, THEN DO NOT BEND IT BACK. CALL A PROFESSIONAL. Do not leave screws loose. Connection must be tight. Fire hazard, otherwise. If you bent nothing, then gently push element back through insulation until mounting plate is flush. Screw into position. Replace racks. Replace door. If you decide to check insulation and other leads, now is the time. I checked mine and it's a good thing I did.... Unscrew back plate of oven, keeping screws in order. Remove plate. Check that your new element and insulation aren't bunched up or otherwise in a hazardous state. You may notice burned or greasy insulation. You may see burned leads on light receptacle and broil element. If you do, then replace them, too. When finished with everything, replace back plate. Put range back into position, ensuring level and plumb. Plug in. Turn on breaker. Pat yourself on the back. You just saved $100-$250, depending on where you live.

1. Make sure electricity is off!
2. Remove 2 screws at rear of oven where the bake element is attached.
3. Pull out far enough to remove the 2 screws where the wires attach.
4. Lift out the old element and set the new one in.
5. Reattach the wires.
6. Reattach the element to the rear of the stove.
7. Turn electricity back on.

New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!

Simple repair that was complicated by not being able to remove the oven door, leaving a long reach to the element connections in the back of the oven. Other than the accessibility issue, the repair is easy. Remove two scews, pull the element out about 3 inches to access and unscrew the screws holding the wires to the element. Then reverse the process with the new element. But, because of the long reach, there were alot of dropped screws and cussing.

1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.

Replace part an wires

First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.

I removed the screw holding the tilt mechanism to the range top. Removed the clips holding the block together. Disconnected the two power leads on the old burner and replaced with the new burner. Closed the block around the leads. Screwed the tilt mechanism back to the range top and that was it!

Installed new knobs, mom is happy!!