JKP62G0K2 General Electric Range - Instructions

It was quite easy. We first turned the power off at the main power switch. Once the power was off, we removed the two screws that fastened the metal plate in the back. We pulled the old bake element out and removed the two screws that fastened the element to two wires. To fasten the new bake element we simply reversed the procedure.

Turned off breaker, unscrewed holding plate, unscrewed element from electric connection wires, replaced element and screwed all back together, turn on breaker, oven working fine now. E-Z!

Removed the broken one by disconnecting the two screws , yellow and red wires and replacing it with the new part you sent me. Very simple.

The removal- replacement problem basically involves the shortness of the connector wires to the terminals. Because the burner is close to the top there is little room to use a screwdriver. The old unit used metal screws. The new came with open threaded holes in the terminals with two threaded screws. Used a small 1/4" ratchet which worked OK, but had to carefully bend the ends of the terminals to allow me to lower the element to an angle that would all room for ratchet action. (All design engineers should first have to work in maintenance before going to drawing board!)

S. Cooke, Houston Texas

On Thanksgiving Day, we were making a pecan pie. The lower oven started to smoke and flame. We quickly turned off the oven, removed the pie, and noticed that half of the lower burner element had turned into cinders. I copied down the part number and serial number of the oven, went to Google, and found the replacement part that I needed. Once the oven had cooled down, I turned off the circuit braker for the oven and tried to remove the burned out heating element. The good news was that I could remove it with my SAE socket set. I then ordered the part on line, knowing with confidence that I could do the replacement myself.
The part arrived one day after I got the email that the part had shipped. That is great service!
I waited till the next day to do the repair since I needed to have the right tools lined up and I needed to wear clothes that might get dirty when working deep inside the oven. A flashlight and a socket set with a 1/4 inch drive were the main tools I needed to do the electrical connections and the oven connection. I also used a blunt putty knife to clean out some of the goo in the oven.
After the repair, I turned the circuit breaker back on and placed a separate oven thermometer into the oven for the first test. The oven worked just fine at 250, 350, and 450 degree settings. Wife is now happy!

Throughout, I took care to not rest my full weight on oven door, although it's hard to work with arms extended. Shut off power to oven at outside circuit breaker, removed both racks, placed trouble light on open oven door at left to illuminate back of oven. Tilted element up to get at bolts. Used 1/4" socket set to remove two hex bolts holding burned-out element's plate to back of oven, pulled it out 3" to expose wire connectors. Held connectors still with pliers in left hand (to not bend wires) while loosening/removing connector bolts with socket set in right hand. Took effort to loosen. Removed element. Wiped oven floor clean. Positioned new bake element in same place, again held connectors still with pliers (left hand) and tightened wire connector bolts with socket set (right hand), pushed element back to original element's position. New element came with screws, not bolts, so used magnetic Philips screwdriver to get screws lined up (tricky), tighten new element's plate to oven's back wall. Removed trouble light, restored power, set closed oven for "bake" and "350 degrees." Element glowed hot in 1 1/2 minutes, ta-daah!

took the element screws off, a little bit dificult to fine the small wrench socket to disengage. I had to have my husband do it because I have too short arms.
I can't believe how much money we saved., the part was there within two days and installed, for a total of 52.00 including next day Fed ex.
Feel good about the whole expierence.

husband said he would call repairman. I found you and ordered part. By the time my husband got around to calling the repairman, I was finished.
Only trouble was getting my hands to work in the small space. The cover plate was not as big as the former unit so I had to muscle it on. BUT, it was a very easy process and we saved tons of money on a repairman and a new oven/micro. THANKS.

Took the old one out and replaced with the new one. It was just awkward to get at.

New element arrived in a couple of days! We turned off breaker to oven, removed the old one which only involved two screws. Then we had to connect new one and re-attach metal square, only tricky part was getting the metal square positioned correctly but that was really not hard, just made sure insulation was covered and plate went back in same position. If we had called a eepair company it would have taken a week or more and probably been expensive!

My petite 69 yr old wife replace element in about 15 minutes with no problem..Also product arrived within a short time frame and your online instructions were accurate. Thanks

I have to admit that I tried to remove the element myself but I did not have the right tool for the last two screws. If I did it would have been very easy. I ordered the part and had someone else put it in so I cheated.

On thanksgiving day, as we were pre-heating the oven, electric sizzle, sparks and a little flame comes from our 24 year old oven. We were able to get dinner on the table and that evening I went looking for what I thought was going to be a difficult to find part. But I found the part on partselect. I ordered that evening and got it on saturday. Installation was a snap. The most difficult part was the nuts holding the wires were stuck on from time and heat and I worried about the wire from the small plate to the coil might break. A little wd-40 and a few minutes and they popped right off and right back on. Works great now.

First job was power off! Next step was to remove the two screws holding the element to rear wall of oven. Next is was to gently pull the wires through the hole as far as possible. At this point I needed pliers to stabilize the joint while I removed the two screws of the electrical connection. Now it was easy to clean the oven to remove arc residue. Now it was a matter of reassemble. Hardest point was getting the screws started in the electrical connections without cross threading while reaching in over the door. Use pliers to ensure you don't bend the connection wires on the element. Finally remount the element with the two original screws. This was the second element to fail. Last time I removed the oven door for better access. I think it was quicker with door on but a lot more bending and reaching.

Turned off power. Unscrewed two screws and pulled old element out of oven. Disconnected the two wires. Cleaned oven thoroughly, held new bake element with soft rag so as to not get fingerprints all over it. Wired new element and screwed it back into oven.

Baking sweet potatoes as I write, they will be delicious with my black-eyed peas and ham, a New Year's tradition in my neck of the woods.