JSC27G4H1 General Electric Range - Instructions

Received the Drip bowls and Rings very quickly. Opened the box and then cut open the plastic wrap that the individual rings and drip bowls were in. Lifted the burner on the stove top, took out the old ring and drip bowl. Installed the shiny new drip bowl and ring, then lowered the stove top element back into place. I was able to replace all 4 of them within 5 minutes. Made the 30 year old stove look brand new.Thank you for perfect fit parts and fast delivery.

unscrew hinge support screw w/nutdriver, remove ceramic insulator held on with clips around wires and base of burner, remove screws holding wires to element w/nutdriver, replaced screws on new element w/nutdriver, replaced ceramic insulator held together w/ clips, reattach hinge, replace burner lower overflow bowl and trim ring, fire it up. used pliers to hold the wires and burner element together when tightening screw so as to not bend element.

First turned off the circuit breaker. The two screws holding the element in place were removed. Next the element was pulled out about 3 inches. Wires were disconnected. Old element was removed. Wires were then attached to the new replacement element. The element was then re-attached to back of oven, using the two screws. Circuit breaker turned to on. About 5 minutes. Took longer to change the flashlight batteries!

So this ancient stove we inherited when we bought our house had the drip bowls wrapped in tin foil. We've searched EVERY (not joking) store in our area for drip bowls that would fit it, but apparently Hotpoint wanted to make sure you could never do this - well, at least not easily. No one, not one store carries drip bowls to fit it. I finally searched online and partselect.com came up first on the list. I was amazed they had the right part! Better yet, ordering was beyond easy, and they came super quick. Popped in the parts in less than 2 minutes, and we're good to go - makes this old stove look new! (well, if this was the 80's, lol) When I clicked on the part it said which stoves it would fit, which was also very helpful. Thank goodness for Part Select! Otherwise we would've had to rewrap those disgusting old bowls... I'd recommend this site in a heartbeat!

Moved stove from wall, unplug the stove from the wall outlet, remove the oven racks, unscrew the plate against the oven wall supporting the element with a small adjustable wrench, pull out the element slowly without tearing the insulation & stretching the two wires, unscrew with a phillips screwdriver each wire with care, as a precautionary measurement: do not make contact with the other wire and any other part of the stove, even though it was still unpluged. Install the new element in reverse procedure...turn on Bake Element on low temperature..when it glows when hot..ready to go.

this repair is simple. Just unscrew the existing connection and attach the new heating element. You may have to break the existing ceramic element, but a new one comes with the new heat element.

shut off electricity to the range, removed the screws holding the element in place, pulled the element out as far as it would go, removed the screws holding the wires in place, tossed the old element, attached the wires to the new element, pushed the element back into place and reattached the screws holding the element in place. Turned the electricity back on and the oven heated right up.

Also, the part arrived the day after I ordered it. Great Price & Great Service.

Removed single screw securing the old tilt-up burner. Removed clips on sides of clamshell ceramic terminal block with flat blade screwdriver to expose two wire connections. Removed 2 screws connecting the wires to the bad heating element. Did not use the supplied new ceramic terminal block, just reused old one. Connected new burner to wires with 2 screws. Reassembled terminal block with clips. Fastened clip with single screw to attach new unit to side of opening in range top. Tested. Done.

Replaced all the ordered parts, and straightened a bent "rest piece" (one of three) on the element os the large burner, which made it rest perfectly on the new Trim Ring. It doesn't easily fall down into the bowl now while I am using the burner. The new Bowls look so nice, and the stove looks nearly new!

I now know where to go for help when I need to repair appliances. You seem to have everything that could possibly be needed. Thank you!

Removed racks from oven. Each element had two screws, used socket wrench for all, gently pulled out element to exposé wiring removed wires with same socket. Once element out of oven, reattached wires to new element, reset element to back of oven and with the two screws attached back. Did the same process for top element only exception was a bracket holding top element from leaning down. It had two screws all the same size as element screws. Once all back in place turned on breaker to check each element.

Easiest thing I've done. Shut off breaker. Unplug range. Pull out from wall (because this is a good time to remove the back, clean under and around the unit, check out the insulation and electrical contacts....or skip it, whatever). Open oven. Remove door (while ajar, pull up). Remove racks. Unscrew mounting plate from back interior wall. Set screws aside. Gently pull element forward until the leads and wires come through the insulation. Remove any strands of insulation that stuck to the leads and connectors. Unscrew leads. Keep left wire to the left and right wire to the right. DO NOT CROSS. Set screws aside. Discard old element. (This is a good time to clean your oven, if you haven't in a while.) If you cleaned oven, wait until dry. Position new element, feet down, in bottom of oven. Position left wire on left connector. Screw tightly BUT DO NOT BEND LEAD. IF YOU BEND IT, THEN DO NOT BEND IT BACK. CALL A PROFESSIONAL. Position right wire on right connector. Screw tightly BUT DO NOT BEND. IF YOU BEND IT, THEN DO NOT BEND IT BACK. CALL A PROFESSIONAL. Do not leave screws loose. Connection must be tight. Fire hazard, otherwise. If you bent nothing, then gently push element back through insulation until mounting plate is flush. Screw into position. Replace racks. Replace door. If you decide to check insulation and other leads, now is the time. I checked mine and it's a good thing I did.... Unscrew back plate of oven, keeping screws in order. Remove plate. Check that your new element and insulation aren't bunched up or otherwise in a hazardous state. You may notice burned or greasy insulation. You may see burned leads on light receptacle and broil element. If you do, then replace them, too. When finished with everything, replace back plate. Put range back into position, ensuring level and plumb. Plug in. Turn on breaker. Pat yourself on the back. You just saved $100-$250, depending on where you live.

1. Make sure electricity is off!
2. Remove 2 screws at rear of oven where the bake element is attached.
3. Pull out far enough to remove the 2 screws where the wires attach.
4. Lift out the old element and set the new one in.
5. Reattach the wires.
6. Reattach the element to the rear of the stove.
7. Turn electricity back on.

Moved into a house built in 1976 about 7 years ago that came with an old but nice looking GE electric stove.
Stove worked well until about a year ago when the switch for the 8" element became erratic. Having been raised where DIYS was SOP I didn't even consider calling for help instead, armed with the stove model number, I went to the internet (How on earth did I ever survive before internet?) and found this site where I quickly found the exploded view of my stove, IDed the switch, ordered and received it within a day or so. Fantastic turn around time!

Now I've never ever worked on an electric stove so I was quite methodical in my approach.

First I read the instructions (you know, when all else fails…) that came with the new switch, then I pulled the stove out, unplugged it and removed the tin back that covers the switches. I drew a diagram of the old switch orientation and which wires attached to what. Then I disconnected the wires, removed the knob and the two screws hiding behind it that hold the switch to the stove.

Oops, the new switch was not identical to the old!!

First: I noticed was that the stem for the knob was longer BUT they proved break off notches so that it can be shortened.
Second: the stem on the old switch was a half round while the new stem was square. I tried the 'half round' knob on the square stem and it went on firmly. Nothing ventured nothing gained.
Third: the terminal orientation did not match. So armed with my diagram and the instructions I made sure I knew which terminal was which (they are labeled). Once assured I knew what went where (I made notes) I installed the new switch and attached the wires (following my notes).

Being an optimist I reinstalled the tin back, plugged the stove in and pushed it back into position before (with my legs, arms and fingers crossed) I tested the switch (which was not easy considering the position I was in). Lo and behold, no puff of smoke and…ta-da…everything worked as it should.

All in all, upon receiving the switch the whole thing took less than 30 minutes.

Recent.

Less than two weeks ago one of the 6" elements fell apart, still worked but lost the supports that rest on the trim ring. Back to the internet to ordered a new element and new trim rings (just for the cosmetics). Again great service, I think I received my order the second day.

Along with the element they also supply new screws plus the spring clips which hold the ceramic insulator together. There's only two wires to contend with so its easy to determine which is the left wire and which is the right. The old terminal screws were locked in pretty good so I used pliers to hold the terminal while loosening them. There's very little slack in the wires so it was a tad awkward reattaching them to the new element.
I did notice that the threaded hole on the new element seemed to be slightly larger than the old. I noticed this when I used the old screws, one would tighten, the other did not so I replaced with the screws they supplied (Duh!). Well I do have an excuse, the new screws were longer which I feared would prevent the insulator from 'closing'.
I probably spent the most time attaching the insulator. I found I needed to fiddle with position of the terminals before the two halves of the insulator would meet. I splayed the wires out slightly then cocked the wire ends slightly so that the wires would neatly leave the side of the insulator. I also adjusted the terminals and the bendable wire part on the element so that they were parallel to each other.

ANYBODY can do this

I removed the screw holding the tilt mechanism to the range top. Removed the clips holding the block together. Disconnected the two power leads on the old burner and replaced with the new burner. Closed the block around the leads. Screwed the tilt mechanism back to the range top and that was it!

I just replaced them.