JB910TK6WW General Electric Range - Instructions

replaced lights in refrigirator and freezer

Removed door from range(see manual for instructions). Set door face down on protective cloth material .Remove two top screwws, 3 bottom screws and lift back of door off. Remove two screws on each side of door bottom channel and remove channel. Put in new trim on bottom of glass window and put screws back in. Set back of door on top of front cover and screw two top screws and 3 bottom screws back in. Set door back into range. Lock clips on both hinges.

The part was exactly what we needed. However, we didn't find the video online to show how to replace the part until we were almost finished. (https://www.youtube.com/watch?v=ovwcJhfWHXQ) If we had found the video, it would have saved us a lot of time because we undid more of the door than we needed to. Also, the video tells you exactly what size tools to use. However, taking the door more apart allowed us to clean more of the inside of the door. So, watch the video before you start, and also, be prepared to spend time cleaning the insides of the door. Also, when we put the door back together, we accidentally turned the front glass panel of the door upside down and it wasn't noticeable until we had put the door back on the oven. So, we had to take it apart again to fix it. All said, we're very happy with the new part. Thank you PartSelect!

it went well as compared to getting a new ~~800$ cooktop and ~~150 to install, I took a shot for 30$ bucks and it worked great!! problem solved and great support ! !! thanks for all your help

Not only did we (my wife did help) replace the dual element but afterwards we realized the control switch was not functioning properly and so that was replaced as well, and now our appliance works as intended. Also the instructions, are helpful as well. We used care not to force or over tighten anything and with two sets of eyes and the extra hands everything went much better. Anything that was removed was noted as to it's location and replaced .

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Removed old switch, put metal jumper from old switch to new one and connected wires to the new one . Reinstalled. Works great.

I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last was feeding the ends back into the slot in the door.

Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.

First, disconnect electrical power to the stove by turning the main fuse to the off position. Confirm that there is no electrical power in the stove. The ceramic top is held by 10 screws that are closest to the ceramic surface. Other screws hold other parts of the stove and not need to be touched when opening the stove. Once the ceramic surface is off there is access to the burners and the various lights and switches. It is important to determine whether it is the burner that is defective or the switch. Inasmuch as the switch has many moving parts, the switch is more likely to be the defective part. Check the switch by gaining access to the switch connections. There is a metal frame held by two screws on each side in the outside of the stove (same area where the initial 10 screws were removed to separate the ceramic surface). Remove these screws and flip the switch assembly so all the wires and cables are accessible. I checked the switch with a continuity tester and by trial and error determined that there were two connections that in all the remainder three switches had continuity when the switch was in the on position while the suspect switch did not. Replaced the suspect switch by pulling the wires and replacing them in identical positions in the new switch (a smartphone camera became very useful to remind me were exactly each cable's connection was). Restore power by turning the fuse to the on position. Check that the burner lights up. If not, change the burner as well. Same simple procedure of disconnecting and connecting cables to the burner). Make sure to disconnect power before working on the burner. Replace the screws that hold the switch assembly. Replace the ceramic top. Replace the screws. Set stove back in its hole. Reset fuse. Total time: 35 mins. Total cost: Approx $25.00 (switch + delivery). Quoted repair by local appliance repair service: $487.50. No contest. Next project is to fix a leaky water dispenser in the refrigerator.

Remove old stained gasket and replaced with new. Only $57.00!

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.