JB910TK6WW General Electric Range - Instructions

Watched video

The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor.
Swapping the sensor was extremely easy. You take off the back panel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.

This temperature sensor is very easy to replace. There are two screws inside the oven in the top middle of the back of the oven. Take these off. on the back of the stove there is a metal plate with 5 screws I believe. Take these off with a nut driver. Then you will see a white connector coming from the spot where you took the other screws off. Take the white connector apart and pull out the temperature sensor from the inside of the oven. Then put the new one in.

Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!

Just note the wire colors and match them where they go on the new control, remove and replace 7 screws and a zip tie and I was done.

Performed repair using a video for reference.

I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last was feeding the ends back into the slot in the door.

Watched youtube video. Very easy to replace

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.

Unscrewed the stove top and replaced the element.

Ordered the part. Received the box damaged and did not realize the part was damaged until our son came all the way from Columbus Ohio to install it. We ordered another part which came in a timely manner. Even though I reported the problem and told them that we are not very computer literate they still would not accept that the part was damaged until we sent a picture. Our son came back from Columbus to install the new part which took about an hour. He took pictures which I was then able to send. They then asked for a serial number. I had already sent all the numbers from the part but that is when they said they wanted the serial number from the stove. We are elderly and getting that required me getting on my hands and knees to get it near the floor. Luckily I was able to get up. After multiple emails I now have to send the part back. Good luck to anyone working with this company. I will be waiting for them to reimburse me for the defective part.

Not only did we (my wife did help) replace the dual element but afterwards we realized the control switch was not functioning properly and so that was replaced as well, and now our appliance works as intended. Also the instructions, are helpful as well. We used care not to force or over tighten anything and with two sets of eyes and the extra hands everything went much better. Anything that was removed was noted as to it's location and replaced .

The part was exactly what we needed. However, we didn't find the video online to show how to replace the part until we were almost finished. (https://www.youtube.com/watch?v=ovwcJhfWHXQ) If we had found the video, it would have saved us a lot of time because we undid more of the door than we needed to. Also, the video tells you exactly what size tools to use. However, taking the door more apart allowed us to clean more of the inside of the door. So, watch the video before you start, and also, be prepared to spend time cleaning the insides of the door. Also, when we put the door back together, we accidentally turned the front glass panel of the door upside down and it wasn't noticeable until we had put the door back on the oven. So, we had to take it apart again to fix it. All said, we're very happy with the new part. Thank you PartSelect!

it went well as compared to getting a new ~~800$ cooktop and ~~150 to install, I took a shot for 30$ bucks and it worked great!! problem solved and great support ! !! thanks for all your help

Turn off breaker, disconnect electrical wiring, remove cooktop from courter top, turn over , remove switch.