JMC27G3J1 General Electric Range - Instructions

Read and follow the instructions. Be careful when stripping old wires to attach to new element. Fit the element to ceramic casing prior to attaching wires. If new element does not seem level after replacement heat a large pot of water. The element will expand and the weight of the pan of water will settle the element. "Physics 101"

Hi, First unplug appliance ,remove the oven door by pulling it up from the hinges, giving room to work deep inside , remove the two screws that hold the element in place. then pull the element out carefully not to stress the wires and replace the element . Note after all is done test with an oven thermometor :)

I initially only purchased the heating element since this usually the cause of the broil element not functioning well. It took a little longer to receive because I had to order it over the Holidays. Once it arrived it was very easy to replace. It worked very well after installation but the broil element still did not function. I then purchased the broil element and received it within approximately 4 days. It took just a little more time to replace because there was a brace that was attached to the upper oven that helped to hold it in place. Once the wires were attached with the screws it worked very quickly. It's nice to have my oven back in use again!

Unplug range from its 220V source. Make sure range is not hot from recent usage. You’ll need a #2 Philips driver, preferably one with 14-18 inch length. The old screws will likely be very stubborn about coming loose. Two of them hold bottom element in. Remove the back panel so access to the two connectors on the bottom element are easily removable. Be very careful not to the let the wire connectors from the heating element drop down into the insulation. For the top element, there are four screws holding it in place, I found it was easier to access these two screws leaning the range backward at a slight angle. Take special care again not to let the wires drop down into the insulation. The connectors to the old element will likely need some extra effort to remove. The reconnection to the new elements should be ok. Make sure all screws go back in that were removed. The new elements will be amazing, and baking and broiling will be like new again.

remove 2 screws pull out, and had a little trouble with the 2 power lines(breaker turned off), as they were around 60 years old, used a nut driver, and plyers to hold leads, and reversed to install. went well considering the age of the oven. tested, broiler works well,(let it heat up for appx 2-3 min to burn off dirt, etc)

1. Cut power off. 2. Remove old element, make sure you do not lose the screws, pull the connecting posts out and we used strings on posts so they could not get lost in the wall. 3. We then replaced the new element with little of no problems, it took approximately 30-45 minutes for the whole process.

This range is about 30 years old and I was thrilled to still be able to get the bake element, which burned out about a month ago. I was doing research to buy a new stove when a cousin, from out of town, called to say they were going to visit the following week. No time now to get a new one installed. "partselect.com" was the fastest way. THANK YOU!

First off, I want you to know I'm an obese 56-year female without tools. But, I knew where to borrow those.

I first shut the power off to the range. I then disconnected the 2 screws that hold the element and pulled it out to reveal the 2 screws which connected the wires. I unscrewed those and removed the bake element. I double checked the stove model and bake element part # at the GE website and ordered it from "Partselect.com". It came in about 3 days. I then reversed the order of the above and it was done.

Here are some challenges I encountered..
1) The oven door was in the way making it uncomfortabe to get to the back of the stove.
2) Those $#%& screws are so short I kept dropping them.
3) The wires in the back bend easily. Be careful.

That's about it. It was a pill but not a real problem. It sure beat buying a new range before I've decided on which one to buy.

I didn't turn the power off which was risky and dangerous, however it was very easy just removing one screw a couple of wires and installing the new one. VERY EASY!

First shut off power to the range in the electrical
breaker box (its the 220 breaker) as marked.
Remove the oven door ( open part way and lift up) the
door will come off.
Remove the 2 screws that the element is attached to the
back of the oven wall. Pull element out part way and
disconnect the 2 wires. Take out element.
The new element had different connections so I cut off
the clips stripped the wires and attached to the element
connection . The element had connections that this was
possible. Push wires back into oven wall and install the
new element with the 2 screws that were removed. You
could also put on clips to the 2 wires that attach to the
element if so desired. (Eye hole clips.)

took cover off back of stove. Removed two screws and wires that were attached to the element. Removed old element and installed new element. An easy repair.

At 76 I no longer do my repairs so I asked my daughter's friend to do it for me.

The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.

Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enough slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!

took old element out , put new element in.very easy.

1. Turn off power to range and remove element.
2. Remove clips from ceramic guards.
3. Disconnect wiring.
4. Connect wires to new element.
5. Install ceramic guards and clips
6. Attached element to range.
7. Restore power.