JKC06G1J1 General Electric Range - Instructions

I received the kit two days after I ordered it, opened it and installed the knobs in less than 3 minites. The knobs were exact matches for the broken ones. The stove top now looks great and I cannot understand why I waited so long to make this simple repair.

With great ease. Only thing I would have appreciated was knowing the size ofvthevrequired socket wrench. Otherwise it was easy and fun as the instructions were crystal clear.

No. 1 thing I did is I unplugged power supply to oven, second- unscrewed two screws that was holding cover plate and removed cover plate with a set of pliers, pulled element out and unscrewed two screw with power wires and installed new element, tightened screws and re-installed cover plate, tested oven turning on oven and in a few seconds element got hot, job done!

First I turned off the breaker to the oven,
then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I placed the new element in the oven, reconnected the wiring and replaced the two screws in the mounting bracket. I reset the breaker and turned the oven on to about 450 degrees for 30 minutes to burn off the new smell of the element. This job was very easy and I saved about $100 from paying a service to do it.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.

every thing went just fine. A simple job at best.

What went better was the prompt service.

Thanks

Turned off circuit. Unscrewed old element. Connected new element and screwed it in. Worked like a charm. It shipped very quickly. Could not be more satisfied; total repair: $30 and prevented me from buying a new oven; satisfaction: priceless.

My sons helped with that. They had to use a pliers to remove the old screws (did not have to notches). After that they they removed the element. Then the wires had to be disconnected (after we unplug the oven from the main power source. Then the wires were connected to the new heating unit. We only got one screw in so far will work on getting the second one in when they return tomorrow. I did turn on the oven and it works!!!

Thank you to the nice young man that helped me on the phone.

This job was easy. I removed two screws to release the element from the back of the oven, two more screws to release the electrical connection, connected the new element with the new screws provided and reattaced the heating element to the back of the over. It took two tries to get the element so that is sat level at the bottom of the oven. Ten minutes later, I was making dinner!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, and reconnected the two wires back with the new screws. Reinstalled the element by reassemblyinig the two screws holding it in place.

Ordered the part online, received it in a coupledays and my son-in-law installed it in a flash. The cost was very reasonable also. The whole experience was a snap. Thanks so much!

I noticed two screws held the heating element in place. I removed the screws. Pulled the heating element out a few inches. Removed the two additional screws which held the two wires on.

To install the new element, I used the two new screws that came with the element to attach the wires to the element. Insert the element into position and attached the element to the rear wall with the two screws which were first removed.

turned off the electric at the breaker box.
removed the door, and racks. unscrewed two bolts, pulled out and unscrewed the leads. reattached the leads, and pushed in and reattached the element.
put the racks and door back on. turned on the electric and then tested the oven. easy!!

I made sure the power was off. I removed two screws from the mounting plate, then I pulled the heating element forward two inches. Where the wires were attached by two screws, I removed those screws also; the heating element was freed up. I then removed it and replaced the 28 year old heating element with a brand new one.

The part was very easy to locate on the website. The shipping was very fast and the part was easy to install!