KD835ADD2 Frigidaire Range - Instructions

I followed instructions on the partselect website. I've never fixed any appliance before, but the directions were very simple and the oven was running again in less than ten minutes.

used the pliers to remove the screws, gently pulled back the element exposed the wires gently pulled the clamps of the element, removed the element. put the clamps back on the new element, put the element back in the holes and put the screws back in.

Ordered the element from partselect. got the part fast. 2 days. removed the old element 2 screw and 2 wires.installed new one in reverse order. total of 10 minutes and oven is working like new. thanks partselect

My husband removed the broken element within a few minutes & was able to install the new part in the same amount of time. Even though this was the recommended part for my oven it was slightly larger than the previous element, but all the important parts fit fine it's just a little bit longer (back to front) than the other. Oven pre-heats 3 times faster than before & cooks evenly again, very satisfied with it!

I am 75 year old female and this was a really easy job. Removed screws from rear of oven. Pulled towards me. Removed wire connections and connected to new part and replaced screws. You will notice an odor when you turn oven on. It will disappear in a few minutes. Don'T FORGET 2 TURN POWER OFF BEFORE BEGINNING

The wire connectors were burn too, that may have caused the Element to burn-up on the end. The Broiler Element wire was getting bad too, so I replaced the old connector. Everything is working fine,I'm glad you guys were there.

i took two screws out and pulled the element out unplugged the wires put the wires on new one and put it back in place and screwed it in done less than 15 min. ordered part on line Sunday and had it by that Tuesday. very fast del.

I ordered a replacement heating element for the bottom of the oven. All I had to do was to remove one screw on each side holding the element in and supposedly pull the element out to expose the spades on each end to unplug them and plug the new element in. As I did that, I touched the metal case of the oven and welded the spade off of the old element. I couldn't pull the old element out into the oven. First lesson---unplug the stove before doing this! I think that the reason I couldn't pull the rods of the element out into the oven is because they were tangled in the insulation. I then took the back of the stove partially off, pushed the rods out the back holes to expose the spades. The one that was melted could still be pulled out, so then I just plugged the wires to the spades on the element, pushed them back and put the screws back in on the inside. Another tip would to have a screwdriver that fits well. These were really tight, and you could strip the heads of the phillips slots. Anyway, the stove works fine. I could have pulled the elements with the wire into the oven, but since I had a welding job because I didn't turn the electricity off, it took me longer.

Unscrewed and unplugged old element, then put new one in it's place. Quick delivery and satisfied with DIY job.

I removed the old part, went on your website and found the proper replacement part ordered it and received it the next day. Two screws and the new part was in.

Removed oven racks; removed the two hex head screws holding the element in place; disconnected the two wires that attach the element to the range. Attached the two wires to the new element; replaced the two hex head screws; replaced the oven racks; tested the element. The whole process took about 10 minutes!! And it's something I haven't done before!

The repair worked GREAT! It took less than 10 minutes and now the oven heats to 400+ in 5 minutes...the element came via regular shipping in 3 days. We were ready to buy a new slide in unit for 1000.00, now we have a 23 year old oven that works better than when it was new!! All for around 30 dollars. THANK YOU!

because of all the info and videos on your site i found this very easy. Thank you for all the helpful info.

Removed the old element by removing two screws and pulling the ends through the back wall. Removed the wires simply by unplugging them. Plugged wires into new element, put back through back wall and secured with 2 screws.

The appliance repair service had never heard of this old brand, but I was able to order this and have it shipped at a more economical price than any other appliance parts service. All the repair service had to do was to walk in and install.