REGS38BNW2 Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Columbia, MD
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven not heating properly
Replaced the baking element by removing two small sheet metal screws and unfastening the two medal clip/leads. Replaced the heating element, reconnected the leads, and refastened the screws. Took not much more then 5 to 10 minutes and the oven now heats perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Dayton, TN
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven element burned out
Plugged in new element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from Efland, NC
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bottom burner not working
I just watched the video, unplugged the stove, attached the burner and started baking again. DSC
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Virginia, MN
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burnt Out Bake Element
1. Remove two screws securing element to rear wall of oven. 2. Carefully pull element forward until you have access to the wires attached to the element. 3. Carefully pull the push-on connectors from the element. 4. Push wires onto new element. 5. Carefully push element back into oven wall and secure with screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Lawrenceburg, IN
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
My oven bake element stopped working.
It was too simple. I unplugged the oven. Unscrewed the old element. Disconnected the wire plugs from the element. Plugged the new element in to the two wires and screwed the new element in to the back of the oven. DONE! There are several Youtube videos that document this process if you want the visuals.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from leominster, MA
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
bake element burn't out
shut the breaker off , remove the racks' use nut driver to remove the 2 screws, carefully slid the element ends out of the holes, disconnected the wire ends (push on connectors) discarded the old element and replaced with the new in reversed order. very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kathy from Eatonville, WA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
change baking element
unscrew disconnect wires put new one on make sure you turn off power
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAMELA from SAINT HELEN, MI
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Replacement of oven element
My husband had no problems except the end of the new element was different than the original, but hooked it up ok!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Abigail from Newark, OH
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven was not getting hot
It was fast and easy! I unplugged the oven, unscrewed the element, then pulled it out. Unhooked the wires. Then hooked the wires to the new element and screwed it back on, plugged it in and then started cooking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RALPH from GRAND SALINE, TX
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake Element Burned Out
Took door off and remover racks. . Then took a nut driver and took the two screws out pulled element out and unpluged it from the wires. . . Then put the new element in place attached the wires and reinsalled the two screws. . . And I was done. . . Ready to rock and roll. . . . . Thanks to insructions from parts select very easy. . . . Thanksguys. . . . . . Ralph from texas. .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Cumberland, MD
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
burnt core
remove old replace new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from WAYNESVILLE, NC
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Stove wires were not long enough.
Required taking back of stove off to properly extend the wires to plug in the new element as well as crimping existing plugs to obtain a secure contection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Overland Park, KS
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
inconsistent temperature
At first I used a nutdriver to remove the two inside screws and found that one of the wires were not long enough to disconnect. I had to remove an access panel in the back which only had 5 screws to remove. I took it off, replaced the element and put it all back together. Then my wife tested it by baking an angel food cake which turned out perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Shelby, OH
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
bake element was broken
Took the back off the range to remove terminals from the element then unscrewed the two screws holding the element on from the inside of the oven. Installed the new element, put terminals on element and reinstalled the back of the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhonda from Liberty, MO
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
The baking element burned in to.
Received the order the next day. Unpluged the stove from electricity. Used a 1/4 craftsman wrench to undue the screws. Pulled the old one out and disconnected the conection. Reconnected the new one. Pushed back in place, then re-tightened the screws. Thanks for having it in stock.
Was this instruction helpful to you?
Thank you for voting!