79090033502 Frigidaire Range - Instructions

Replaced control units that were malfunctioning.

Disconnected power first. Removed 4 screws on the back of the range, pulled the knob off of the switch, removed 2 small screws on the switch(on the front , under the knob) pulled off the 4 wires with spade connections on the switch. Put wires on the new switch, put in 2 screws on new switch, pushed knob on switch, replaced back cover and tested the new switch. Works great. Took less than 10 mins.

Pulled the stove away from the wall, disconnected the power cable, removed the top part of the back where the switch was. In front there are two screws that are philip heads that hold the the switch in place. Be careful when replacing the wires. When you take one wire off, place it on the new switch in the the same position. The switch can be put back, but be careful of the angle, because it has four screw holes. Replace the switch, replace the back, plug the power cable in, and push the stove back to it's original position. Make sure there isn't anything on the burner when you test the switch.

Removed bottom drawer. Pulled Range out away from the wall. Unplugged Range. Removed 6 screws from top back cover. Removed top back cover to reveal the Infinite Switches behind the knobs. Pulled the knobs off of the Switches I wanted to change. Removed the 2 Phillips Head screws holding each switch. Pulled the wires off of the old Infinite Switch and put them on the new Infinite Switch. I was careful to put each wire on the correct terminal from old to new switch. I then reassembled the Range in reverse order. I changed both 8" Burner Infinite Switches. I was only having trouble with 1 switch. But, upon inspection. Both Switches had burn marks on the top left of the switch.

The infinite switch arrived promptly and while not a perfect match fit the range fine. It took me a few extra minutes to figure out the wiring configuration, but it was fairly easy. I was very pleased with Parts Select's service.

Confirm the problem and check electrical diagram to see if there was any other circuit in the syatem that could cause the burner to stay on , remove back cover and inspect switch contacts, found them burnt , look up parts for the model number and replace it.

Followed video instructions on your web site.Removing one wire at a time as suggested simplified installation.Somehow i lost burner lens indicator.Ordered it from your website cost $3.84 plus shipping recieved in one day. GREAT SERVICE

Took back cover off 2 screws held the switch then moved wires one at a time from old switch to the new one put everything back plugged in stove everything worked

I watched you vedio and done just as the vedio told me how to change the switch. When I got the switch on pluged it in turned it on and every thing work great. thank you very much.

To find problem. I turn the power off to range. Removed top back panel. Removed switch and found there was a black spot on white covering of switch. So I order a switch. When it came I turn power off to range. Removed the top panel on back of range. Removed one wire at a time and put it on the new switch. Once all wires were on new switch. I removed old switch and installed new one. I then reinstalled the top back panel and turned the power back on. It is really easy to do. If you are not confident enough. Take a picture of the back of range before removing the panel. Then take a picture of the wires before you remove them.

I read other experiences on line and determined that it was either the element of the control switch. So I decided to order the control. When deciding I had removed the upper back sheild and put it back on. Subsequently a couple of days later there were popping noises culminating in a flash and the stove went 'dark'. I figured that I had pinched a wire when I put the upper shield back on. I removed the shield and looked for black 'short' marks. None were visible. I went to the electric panel and tried to reset the 60 amp breaker. It wouldn't reset and momentarily the lights dimmed. Uh-oh! Went back to stove and opened area where the cord connects to the stove. Direct short- a lose terminal block bolt had welded itself to the chassis! I redid all connections and lined inside of stove back with duct tape- also redid the connections with bolts, nuts and lockwashers covered each with electrical tape. Now reconnecting electric I put the new switch in. Removed the knob from the front and started to transfer the wires from the back. This was a little confusing because the control I received looked different from the one in the stove. After some checking I looked closely at the terminals on each control and they had tiny number/letters on them like H1, Li, H2 etc. So I just transferred H1 0n one cntrol switch to H1 on the new switch- L1 to L1 and so on. Put it all back together, turned on power and everything is working great.

removed back. discovered wrong connector on probe. Cut the connectors off and spliced with small butt connector. Took me longer to find the tools and connector than to do the repair. The wires are very small and require a very small butt connector. Tips by the sales rep and previous customer were helpful. Great service. Will try PartSelect for Cub Cadet and Yamaha OB parts. Thanks. John

The video was a great help. I could have replaced the switch without watching it, but it gave me confidence that I was doing it right. Everything went just like he said it would. Burner seems to work better now and no more scary noises.

Would have been simple if Frigidare had not changed the plastic snap wire connector on the part. The replacement part had a different snap together wire connection. After a couple of phone calls stating that the new part and the old part had different part numbers was informed that you have to snip off the ends and use wire connects but it was the right part. Once I knew that it was a simple repair if you have the wire connects to connect the wires.

I disconnected the power cord,took the top back plate off,the switch knob on the switch I was to change,the two screws holding it.pull the old switch out,place the new one in the holder,replaced the two screws that holds the switch and took the wires off the old switch one at a time and placed them on the new one in order on new switch.replaced the back cover and plugged power cord back in.turned range on,it was good. r taite,