79090033502 Frigidaire Range - Instructions

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

I took the brads that were left from the old gasket off with needle nose pliers. Then I put the new one on. It was very easy.

Disconnect power to Range at Electrical Service Panel control box. Remove 240 volt service electrical plug to range. Remove back top panel to expose element control switches. Remove element control switch to L.F. burner by first pulling off the control knob. You may need to use a large flat screw driver to pry behind knob to get it started but it should come straight off. There are two screws revealed under knob that need to come off. Then the element control is easily, but carefully, removed out the back. Be careful you do not pull the "Hot Surface Indicator Light" switch off right above the element control switch. If you do, this will break the end off the plastic "Hot Surface Indicator Light" lens. If this happens you can still replace it but you will need to use super glue to make the "Hot Surface Indicator Light" switch stay connected to the clear lens. Install new element control in reverse order before gluing the "Hot Surface Indicator Light" switch as stated above or you will knock it off again. While holding the old element control in your hand with wires still attached, remove one wire at a time (making note of the location code for each wire) from old element control and install on new control. The new element control layout for the wire prongs will be different so you need to make sure you look for the code (like L1, H1, P) located on each prong location and put the same coded wire from old element control location onto new control prong code location. Reinstall new element control (with wires pushed fully onto prongs of new control) into panel with screws removed before. Reinstall knob, reinstall panel cover and reconnect range power plug. Restore power to Range at Electrical Service Panel control box With electric power restored, test element control by turning it on and see if it properly cycles on and off at different settings. If working properly you should be able to hear it click on and off and element heating and going off accordingly.

It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

I had open back cover and remove the switch than replace new switch. Makesure cable conection.

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.

I had to replace the switch on one of the large elements. It could and should have been a quicker repair if there would have been some installation/wiring instructions included with the part. Other than that the repair went well.

first thing was to turn the breakers off. then pull the range away from the wall. used an 1/8 th inch socket to take off the back panel to get access to the switch.used a Phillips screwdriver to disconnect the switch under the knob in the front. took off the wire terminals one at a time and matched it to the numbers on the old switch.replaced the knob, screwed it on to the range. turned the breakers on and tested the switch.worked fine, replaced the back cover and pushed it back into place.

was easy open the back side of the range and change the part, the only issue was the wire I used the diagram

Unplugged the range. Removed the top section of the back of the stove to expose switches. Removed the knob, (pulls off exposing the 2 switch screws), unscrew & pull out from the back. The new switch was slightly bigger but the same manufacture and post letters & numbers. Transfer wires one-at-a-time from the old to the new switch. Mount the new switch back in place, put the screws in and the knob on. I plugged in the stove for a quick test, HA....works perfectly. Unplugged again and put the back panel back on, plugged back in and pushed the stove back in it's hole. BEFORE; the old switch when turned down would come back on BUT stay on high, a lot of boil overs. FINALLY: when turned on, it would NOT turn off, a real fire hazard. Thank you for having an original replacement part.

1 - Turn off the power from the panel. 2 - Unplugged the range from outlet. 3 - Unscrewed the black hex screws from the rear panel. 4 - Took a pic of the bad infinite burner switch to ensure the correct wires would connect to the new switch. 5 - Removed knob and unscrewed switch, then replaced with new switch. Matched all of the wires to like, L1, L2, P, H1 and H2. If any wires do not exist for your switch, it is ok because not all ranges use all wires.

Take handle off, then back cover. Of course unplug power. Switch wasn't built exactly like the original but all you have to do is connect each wire to the same letter, number code as on the old one . Works like brand new!

Slid stove out, disconnect power plug, removed top control panel with 4 screws. Unplugged two electrical connectors. removed knob and nut removing switch. Re-assembled in reverse order and test all functions.