FED300ESE Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeffrey from Pittsburgh, PA
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Intermittent heating element function
Instructions included with terminal block assembly. Toughest part was to strip the insulator off of the old wires on the stove. I was originally going to just purchase one but after looking at the other terminal blocks and seeing the burnt insulation and some of the wire strands, I just replaced all 4. PartSelect customer sevice was very helpful to confirm the correct part number I needed for my stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TRACY from EASTON, PA
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Existing stove top burner element worn out
Very easy to repair! I removed the old burner and slid the new burner element in its place. It was as simple as that! No tools required. My one and only complaint would be that the old burner was slightly larger (within 1 inch or so) than the new one so the new one sits slightly crooked on the stove top. But it works just fine. The item also shipped very quickly. Within a day or two. I am very satisfied with the transaction overall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claude from Baton Rouge, LA
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Surface element shorted out
Tilted the surface unit and proped it up with the metal arm then I unpluged the old 8"-surface element and replaced it with the new 8"-surface element that I purchased from PartSelect.com. I then lowered the surface unit turned the burner knob on and everything worked fine. Thanks PartSelect.com.
Was this instruction helpful to you?
Thank you for voting!
Renewed drip pans
Replace the old ones with the new ones. Was VERY impressed with the quick delivery!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from cincinnati, OH
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
heating elements not working
prepared the parts as directions displayed, removed the heating coils and popped the hood on the range, simple curcit 2 wires in to the main harness for each coil. snip, plug and twist add heat wrap to seal the new conections and done very simple fix saved me buying another oven....for now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Glasgow, MT
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven was not heating up to the set temperature. Stopped around 180-200F.
Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery from Union Point, GA
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element went out on my oven
Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Hedgesville, WV
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element burned out
Took screws loose, unplugged old one plugged in new one put screws back
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Kettlersville, OH
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner burned out
unplugged old burner plugged new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Fossil, OR
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced burner block
Looked at the instructions and cut the wires, put the new wires in the block, attached the block to the range, put the new wires to the range wires using the wire nuts. I plugged the element into the block turned on the power, tried the element and it worked. It was really a easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Artesia, NM
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Coil melted in half.
First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Reno, NV
- Parts Used:
- 316270201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle broke
unscrewed old and screwed in new
Was this instruction helpful to you?
Thank you for voting!