FEF364FWC Frigidaire Range - Instructions

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Pulled stove away from wall and unplug .Removed grates for better access. Unscewed element scews removed element & tested for continuity.there was none element is bad . Replaced with new one . Time about 20 minutes.

Used instruction video & replaced part.

Turned off power to stove;removed baking racks , loosened Holden screws to pushon bake element removed old bake element,installed new pushon bake element.

This was my first time ever working with electrical issues. My husband is not physically able to do repairs now. Very easy fix. Just viewed video repair instructions and it went exactly as instructed. Within 45 minutes, I had my stove repaired and cleaned and back in working order!! Great results. My range is working perfectly again and Mama is happy!!

This caused the burner switch cotacts to arc burning out the switches. It took 30 or 43 minutes to replace the switches and put the range back together. The bake element took 10 min. ti replace. Grandma has her range back and I am a happy grandpa!! Thanks for the help and we saved over $170.00 for the repairs. Jim Johnson

Turn power off to the stove! Opened the oven door, removed 3 screws holding the top down. Lift the top up. (Take a picture first of where exactly the wires go and where the prongs go) I unplugged the 4 wires from the element. Use a screwdriver and pry the prongs through the metal brace. Remove the prongs from the old element because they are a separate part and don't come with a new element. If you wish to continue to use the stove, tape the ends of the wires up, because they will be hot when you turn any other burner on.

First , I unplugged the stove from the wall !!! Then Removed 2 screws attaching the top to the stove frame , then removed 6 screws from back side to un-do the hinges from both sides to allow cooktop to come forward. Unscrewed 4 screws that held the elements to the 'broken' cooktop glass and everthing was free. No disconnection of the wiring was needed..
Reattached the element brackets to the new glass, put the hinges back in place and laid cooktop down onto stove frame for the last 2 screws to be put on. It worked fine when I re-plugged the stove unit back in ..

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

After a brief discussion with CS about the electric stove part was shipped it arrived and I proceeded to install I found it needed to be installed sideways not up & down like the old one. The terminals did not line up so I put the black lead first and the purple lead last in doing that I burned out the switch??? was not easy to install as the video showed his switch matched each wire? My installation was sideways??

The youtube video clearly described how to remove the back panel and how to replace the probe.
The repair took maybe 20 minutes to complete and 1/2 of that time was spent cleaning behind and underneath the range!
Range is working perfectly now!

Removed 4 screws on back cover removed 1 screw holding probe and unplugged the probe took it out and installed new probe.

First we turned off the electic, then we took the back off the stove and pulled the wire off the bad element then replace the new element. It was very easy to do.

I had open back cover and remove the switch than replace new switch. Makesure cable conection.

Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!