FGFL89CCB Frigidaire Range - Instructions

Make sure you unplug the oven before you begin. I removed the old igniter. The top wire on the igniter goes to the back of the oven and plugs into a flat blade type connector. Instead of using the twist wire nut I used a flat connector because it was easier to put on and is foolproof. Make sure you cut the plastic insulation off the connector so it does not melt when the oven is in use. I used a wire nut on the other wire and that was it. Very simple and the oven works great again.

1) Turn off the gas and disconnect the power

2) Remove oven door. There requires that you remove the two square drive (SD) bolts on the inside, partially close the door and lift it off the hinges.

3) Remove the grills.

4) At the back remove the rear shield (aluminum panel held by 2 SD sheet metal screws.

5) this exposes the broiler igniter and its two wires. If its been replaced in past, there should be two porcelain screw-on wire connectors. Undo the connectors by turning them counter-clockwise. With a volt-ohmmeter, measure the resistance across the igniter. If its open circuited, its broken. If not, then its in the circuit board, and this help stop here. If this is the original igniter, it ends in a plastic connector. Disconnect by pulling it apart from its mating plug and again, check the continuity of the igniter. If its defective, reconnect the connector and cut each wire on the igniter side. Strip back about 1/2 inch of insulation on each lead.

6) inside the oven, using the SD driver, remove the 4 screw securing the broiler burner from the roof of the oven. The burner can now be removed, pulling the burner away from the gas jet on the right.

7) The igniter is now exposed and can be remove by removing the two SD drive screws.

8) Replace with the new igniter, being careful not to touch the black element, and feeding the wires though the rear oven wall.

9)Reverse the above dissembly procedure.

10) Broil the sausages.

I searched the item I needed and followed a link to PartSelect.com. I paid a little extra for shipping and literally recieved the part in two days. The part was an absolute perfect fit and my wife and myself have never been happier. Home cooked meals again thanks to the folks at PartSelect.com. It couldn't have been an easier.

removed shelves and base, removed 2 screws that held igniter on, disconnected wires from gas valve removed protective cover in corner {1 screw}
disconnected plug, removed igniter. This igniter was easier to remove from front of stove on this model

Simple: remove the element by hand and replace new one.

I can't believe how quickly I received my new part -literally next day.

I compaed price at different sites and partselect .com was 30% cheaper for the same item. I received the part in 2 days by fed-ex.
Doing the job was real easy.Just pull the old knob out and put the new one in.

First, I unplugged the oven from the wall. I opened the bottom drawer of the oven to see where the igniter was mounted, which was directly under the bottom pan of the oven itself. I opened the main oven door and unscrewed the 2 screws that were holding the pan to the bottom of the oven. Then, I slid the pan back towards the the back of the oven and it popped right out.

There were 2 hex screws that were holding the old igniter on, so I unscrewed them with my socket set. I made sure to pay attention to which wire was the top one and which one was the bottom one coming out the back of the igniter. I pulled off the wire nuts connecting the igniter wires to the wires of the oven. I striped the wires on the new igniter and re-attached them to the proper wires of the oven, using the included replacement ceramic wire nuts. I re-screwed the hex nuts in, mounting the new igniter to its proper place. I put the pan back and screwed the 2 screws back in to hold it in place.

Plugged it back in, turned it on, fired up within 20 seconds. Good as new.

Twisted replacement bulb into place easily. Let there be light!

Slid oven out removed one screw one plug replaced part took 5 minutes.told parts repair the error message and they sent me the correct part in two days will use them again saved me from Repair man wanted 85 dollars just to look at it my cost was 28 for probe and 8 dollars for shipping already helped neighbor with their stove they needed new ignighter 12 dollars repair place want 110 to come look at it this site walks you through repair best service!!!!

Ordered new racks and replaced them.

The hardest part was pulling the oven away from the wall. Two bolts hold the sensor in place and a clip connects the electronics. Replacing the old one was trivial.

My Tappan Tail:

Open the oven and remove the racks, turn on the oven light.
Remove two screws in the back to remove the bottom plate. Mine are about 1 1/4 in. long.
Remove one nut holding the butterfly plate in place. Ignitor will be exposed.

Turn off the oven light and unplug oven. Don't drop the plug behind the oven, I was ready for that one.
Drop light or flash light will be needed, it's dark in there. And something to sit on, 16" old plastic milk caddy, I just happen to have one.

Remove the two screws holding the ignitor, don't cut the wires just yet. Take note where the wiring runs. Install the new ignitor. My wires went behind the gas piping.

I cut the bottom wire from the old ignitor first, up close to the ceramic. Wire shield can be reused, slide it over the new wire. Cut the old wire, leave a lot. Trim the new wire to desired length and strip the ends of both and use the ceramic cap and connect the wires.
Do the top wire.
Slide the wire shield next to the igniter, adjust the wires so the wire shields won't slide away from ignitor. With the butterfly shield back in place it's time to plug it in and give it a test.
Nice.
Replace the bottom plate of oven, screw holes hard to find. Had to use an awl to find the holes to line up the screws. I also didn't push the front of the plate down into place until I had the screws started. It helped.

You might think this is overkill, but how many of us have ever replaced the ignitor. Not me.
I do a lot of DIY's. I'll rate this as a 1, easy.

What shall I bake first, cornbread of course. I my cast iron skillet.

Working on an old oven is difficult. Please expect the unexpected. The years of heating and cooling play havoc with oven parts. The screws holding the Flat Style Oven Ignitor become stripped. It took extra time to remove them. I had to go to the hardware store to buy replacement screws. Once I removed the old parts and had replacement screws the job was very easy.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.