KTM487180C Frigidaire Range - Instructions

The problem was caused by the owner placing an aluminum catch pan under the bake element. The failure of the element was where it was in contact with the pan. The repair involved removing two screws pulling out the element to access the wires. The connectors were the pull off type so I just disconnected the wires from the old element and placed them on the new element, pushed the element back in place and replaced the two retaining screws. I suggested that the owner not place anything in contact with the bake element. Be sure to up-plug the stove plug before attempting repair.

raise top of stove unplug burner plug in new one done

Turned off range/oven breaker. Opened the oven door. Removed two 5/16 hex head screws. Pulled bake element forward and removed the two slip on electrical connections from old bake element and put them on the new one. Replaced the two screws, closed the oven door, and proceeded to overhaul the kitchen faucet.

this bake element has two special Hex style screws, securing it in place, but a nut driver worked just as well. remove the baking racks, and then loosen the two hex screws. slowly pull the element out of the back wall and then disconnect the electric leads. reinstall by doing then the opposite action. could not have be simpler.

After doing without the oven for a week or so we decided to turn to the internet and try doing the repair ourselves. We are not mechanically inclined/fix it yourself kind of people. This really was easy. Just detach the old element and attached the new one. A couple of bolts and snapping one out and then the new one in. Very simple

My husband removed the screws and took out the heat element and when we received the new heat element in 3 days (thank God!) My husband put the new part in the oven and replaced the screws!! Total repair time was about 5 mins!!!

The repair took less time than finding the model number. After unplugging the range and allowing it to cool I disconnected the element (2 screws), went online and found Part Select ordered the element and saved $16.00 dollars over the least expensive local shop, I was amazed at how fast the element arrived, I believe it was 4 days from order to my door. I went to my local hardware store for some new connectors for the wire, put them on and plugged in the element fastened down the two screws and went back to baking cookies. The element was well and safely packed and came in perfect condition. It works like a charm. Thank You

Unscrewed 2 screws, used pliers to pull off push on terminals attached to element . Slide terminals back onto new element and replaced screws. EASY

Unplugged oven, pulled out old element, reattached new one, making sure to be careful with wires, and put on as secure as possible, just like it was before. . . Very easy to fix

Take out 2 screws disconnect the wires one on each side removed element recoonnected the wires put the 2 screws back in . Also I did flip breaker off while working. When I turned the oven on I noticed it gets bright red almost instantly. I dont remember my old getting red at all. this tells me it probably needed changing a lot earlier. I ordered the part sunday nite it arrived wednesday at lunch.I will definetly use this co again.

removed two screws pulled element out about four to five inches attached wire to new element screwed back in less than ten minutes done

Very simple, 2 screws, replace element, put screws back into place. The BEST thing... ordered on Tuesday afternoon, received on Wednesday afternoon, and Thursday was New Years day. This has been the best service, from any parts company, that I have ever ordered from. Keep up the good work!

using a nut driver I removed to two screws that were holding the element in place. Then simply disconnected each wire. Removed the old element and plug the new wires onto the new element. Reinstalled the two screws and everything works fine

Since I had the element out I cleaned the stove. That took me 2.5 hours. Used cold spray and let sit for two hours and wipe out clean took about 30 minutes. Now for the element itself it took me about five minutes to put the new one in. Oven looks and works like new. Just google your repair needed and watch the video. Easy Peasy. Last time I had it done by an electoral repair person for the tune of about $100.00. This time I bought the part and did it my self. Cost less than $25.00 including tax and shipping. No brainer.

Unscrewed 2 screws, pulled the wires out and unplugged the old element, plugged the new one in, screwed 2 screws back in, so easy anyone can do this, it's nice to have a second person holding a flashlight but couldn't be any easier.