CRE3510LWJ Crosley Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marion from NEWPORT, TN
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
It burned out. Broke to peaces
I watched a YouTube video. Than it was easy. I turned the breaker to range off. Took the nuts off. Uncliped the part. Plug new part in. Put screws back in. Flipped on the breaker. And it works wonderfull.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from PORT ST LUCIE, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bottom element had hot spots, very slow heating
Turn off the power to the range. Remove oven racks. Remove the two screws and slowly pull the element out being careful not to pull the wires off. Remove the two wires then attach them to the new element. Push the element back in place, put the screws back in, turn on the power and turn on oven to make sure the problem is fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Horace from CRUMPLER, NC
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower Heat element burned out.
1.Take no chances. Turn off power at main breaker box (Range). 2 2. 2. 2.Remove inside grills then pull damaged element forward to expose wires and screws. 3. Use nut driver or phillips screwdriver to undo both screws. 4. Remove burnt out element then replace it new one. Make sure both sides are firmly pushed onto the wire terminals before tightening screws. Replace grills. close oven door then turn breaker at breaker box on again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from STUART, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element burnt out and snapped and appeared to try to arc-weld itself back together?!!
Just followed the very simple video instructions…it took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from cartersville, GA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
bake element burned up
removed two screws pulled element out about four to five inches attached wire to new element screwed back in less than ten minutes done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Bradenton, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Baking element burned out
Very simple, 2 screws, replace element, put screws back into place. The BEST thing... ordered on Tuesday afternoon, received on Wednesday afternoon, and Thursday was New Years day. This has been the best service, from any parts company, that I have ever ordered from. Keep up the good work!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Ruidoso, NM
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
While baking cookies I looked in the oven only to find the bake element was glowing white on the curve of the element, then a second spot started to burn. The element was fried.
The repair took less time than finding the model number. After unplugging the range and allowing it to cool I disconnected the element (2 screws), went online and found Part Select ordered the element and saved $16.00 dollars over the least expensive local shop, I was amazed at how fast the element arrived, I believe it was 4 days from order to my door. I went to my local hardware store for some new connectors for the wire, put them on and plugged in the element fastened down the two screws and went back to baking cookies. The element was well and safely packed and came in perfect condition. It works like a charm. Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcus from Gastonia, NC
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bake element burned into while baking
Take out 2 screws disconnect the wires one on each side removed element recoonnected the wires put the 2 screws back in . Also I did flip breaker off while working. When I turned the oven on I noticed it gets bright red almost instantly. I dont remember my old getting red at all. this tells me it probably needed changing a lot earlier. I ordered the part sunday nite it arrived wednesday at lunch.I will definetly use this co again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Aiken, SC
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Baking element burned out
The element went out on a Wednesday. We ordered the part the next day. We received it the following Tuesday (Mon. was a holiday). My 16 yr. old son replaced the part within 15 minutes. It was a piece of cake-actually it was a pizza!!
First and foremost we turned off the breaker, a very important thing to remember!! Then he removed the two screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the two wires...and reconnected the new ones and put screws back in. Voila!! Ours was stillll under warranty, but we would have had to pay the service call and labor costs. Our do it yourself was much cheaper and faster!!
First and foremost we turned off the breaker, a very important thing to remember!! Then he removed the two screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the two wires...and reconnected the new ones and put screws back in. Voila!! Ours was stillll under warranty, but we would have had to pay the service call and labor costs. Our do it yourself was much cheaper and faster!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Hagerstown, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven would not heat up-
Disconnected the main electrical plug from the wall for the oven..
Used a nut driver to remove the two screws that held the heating elementin place.
Pulled the element out so I could remove the two wire terminals.
Installation of the new heating element was fairly basic..Oven is working great..
Used a nut driver to remove the two screws that held the heating elementin place.
Pulled the element out so I could remove the two wire terminals.
Installation of the new heating element was fairly basic..Oven is working great..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gwendolyn from ST PETERSBURG, FL
- Parts Used:
- 316075103
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
I am a 67 year old female with both knees fake..
I sat on a stool and knelt on a pillow (because of my knees) but I got it done and it works great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from NEWCOMERSTOWN, OH
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bottom element burnt out. Bad design on this element.
Turn power off. At oven, removed two screws from element hanger. Pulled old element out exposing spade connectors. Pulled connectors lnstalled connectors on new element and shoved back in stove and replaced screws. Work done with oven door open using drop light. Check for debris, turn power on, turn oven on to check.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from whiteville, NC
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
bake element burnt into
i removed the back panel removed two screws pulled the element out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Pleasant Hill, OH
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element went out
Removed the screws, replaced it with the new bake element, put the screws back in........and bam! I'm back in business. That's how easy this was to repair. Bake element cost me 40 bucks, appliance repair shop wanted about 200 bucks to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from FRANKLIN, NC
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
baking element out
removed the two screws pulled the wires out sliped the connections from the old element and connected the new one .
Was this instruction helpful to you?
Thank you for voting!