CRE3510LWJ Crosley Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- PAUL from FRANKLIN, NC
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
baking element out
removed the two screws pulled the wires out sliped the connections from the old element and connected the new one .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitchell from Sebring, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Banking Element needed replacement
For an electrical appliance, it doesn't get easier then this, this was real easy.
I removed both baking racks, unscrewed two screws holding the old element in place, pulled out element about 1 1/2 inches, removed the wires off of each end of the element, then replaced with new element in reverse order. That was it. Had time to play 18 holes of Golf!
I removed both baking racks, unscrewed two screws holding the old element in place, pulled out element about 1 1/2 inches, removed the wires off of each end of the element, then replaced with new element in reverse order. That was it. Had time to play 18 holes of Golf!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from WASHINGTON, PA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Oven wasnt heating
Took out 2 screws unclipped the part put the new one on and i was done. Very easy fix .. Baked a cake right after to celebrate
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from NEWCOMERSTOWN, OH
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bottom element burnt out. Bad design on this element.
Turn power off. At oven, removed two screws from element hanger. Pulled old element out exposing spade connectors. Pulled connectors lnstalled connectors on new element and shoved back in stove and replaced screws. Work done with oven door open using drop light. Check for debris, turn power on, turn oven on to check.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerry from Mackay, ID
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
N/A
I followed the instructions provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Constance from MILTON TWP, ME
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
oven element did not heat
Pulled out stove and unplugged. Took off back of stove and unplugged two wires. Opened oven door and unscrewed two nut screws to remove element. Inserted new element and screwed two nut screws back. Went to back of stove and replugged.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from INDIANAPOLIS, IN
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would only get slightly warm.
Loosen 2 screw with a 1/4 nut driver. Pulled element out to expose connections. Carefully disconnected old element and replaced with new element. Pushed wires back into holes and replaced the screws. (Note: Be careful not to let the disconnected wires slip back through the holes. This almost happen to me)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from FREDERICKSBRG, VA
- Parts Used:
- 316442300
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner would cutoff intermittently
Pulled out old burner/inserted new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JONESBOROUGH, TN
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burn into
Remove the old one and replaced the new one. It was very simple, fast, and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion from NEWPORT, TN
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
It burned out. Broke to peaces
I watched a YouTube video. Than it was easy. I turned the breaker to range off. Took the nuts off. Uncliped the part. Plug new part in. Put screws back in. Flipped on the breaker. And it works wonderfull.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carol from LAUREL, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element burned through in one spot; oven would not heat
replaced the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from ROCKVILLE, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Broken element
Simple installation took 2 minutes to do...pop on the connectors, screw each end into back of oven...DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from GERMANTOWN, NY
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element broken
Removed old element with a nut driver, 2 screws. Disconnected electric wires on element, being careful not to let the wires slip into the back of the oven. Connected the wires on new element, lined up holes with holes on oven and screwed in 2 screws with nut driver. Done!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from MARIETTA, GA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Element in oven burned through
Turned off circuit breaker to the oven, unscrew the 2 small screws, pulled the element away from the back, pull element away from the wires in the oven and replace with the new one and replace the screws. Tirn circuit breaker back on
Was this instruction helpful to you?
Thank you for voting!