CRE3510LWJ Crosley Range - Instructions

I removed the screws holding the element in place, pulled the element out, and one of the leads came off and dropped into the oven. I had to take the back of the stove off and feed the lead back through the hole into the oven. If I had been careful to keep the leads from dropping out of the hole, the whole repair would have taken only a few minutes. But even so, it was quite easy.

REMEMBER TO UNPLUG YOUR APPLIANCE FIRST!

I simply removed the old drip pans and inserted the new ones which matched and fit perfectly.
I'm glad I found you on line. Your service was fast and the whole transaction was easy!! Thanks.

I unplugged the stove from the outlet, then removed the two burners I was going to be working on and the drip pans. Then I raised the top part of the stove and removed the screws holding the plug-in blocks to the stove. Then I cut the two wires going to the old plug-in block and stripped the wires back to match the new wire parts. Then I placed the sleeves over the new wires, then I placed the new wire beside the wire I stripped on the stove and screw on the wire cap making sure it was tight. I repeated this three more times, once I had all four wires connected I then placed the sleeves over the connections and heated them up until they were formed around the connection. Once I had all the connections done I placed one wire at a time into the plug-in block until it locked into place ( I looked at my old plug-in blocks first to make sure I placed the new wires in the correct way ).I then used the metal mounting bracket that matched my old ones and snapped the correct one onto each plug-in block. Before mounting them onto the stove I compared them to my old ones to make sure they were correct. Then I used the new screws to mount them to the stove. I took a second look at everything I had done before closing the top cover of my stove. After lowering the cover back into place I put both the drip covers in place and then installed the burners.I then plugged the stove back into the outlet and tried the burners. This was very simple and the video on the web site shows this very well which made my job very simple.

shut off power to stove. Opened the oven door, removed the racks. removed 2 screws holding the element in place. gently pulled element out to expose connections. removed connections. discard old element. reattach connections to new element and reinstall. very simple.

The old element burnt a hole in itself and just glowed in an area about the size of a quarter. I unplugged the oven, removed the two screws that held the element and removed it. I plugged the oven back in so we could use the top burners. When I went to install the new element I did not unplug the oven as the controls were off. I did not know the element was hot from the outlet (by design) so when I tried to attach the new element sparks flew and it welded itself to the wire so I jerked it looose. I then unplugged the oven, replaced a blown fuse, and installed the element.

I first turned the power supply off to my oven. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the ends. After that I connected the new element to the wires on my oven and secured the element with the two screws and turned the power back on. I pushed the oven-on button and now I'm back in business.

I pulled out the old element and the new one just plugged right in.

Pulled the heating elements out took the bowels out that didn’t fit, threw them away and replaced them with the perfectly fitting bowels from this site and replaced the heating elements.

I order the Element and received just in 4 days. It is Real incredible. I just opened the box and replaced the burners.

When I pulled the element out of the back panel of the oven to remove it, the electrical connection got caught on the edge of the hole in the panel and disappeared back into the oven insulation. It was difficult to find and pull it back out to reinstall it on the new element.

When I found the part I needed there was an instructional video on how to remove broken bake element and install new bake element. This was the best video short and sweet and anyone...I mean ANYONE could do it!

Step 1- cut off the power supply (I flipped by breaker, but you could just unplug the oven)
Step 2- remove baking racks
Step 3- unscrew the little metal plates inside the oven where the bake element meets the back of the oven (reserve screws for new element)
Step 4- carefully pull the bake element out until you have the wires through the holes
Step 5- carefully pull the bake element from the wire clips on both sides
Step 6- take broken element out of over and put new one in
Step 7- slide new bake element ends onto wire clips
Step 8- slide new bake element and connected wires back though back of oven
Step 9- used saved screws to screw metal plates on bake element to the back of the oven
Step 10- replace oven racks
Step 11- restore power to range
Step 12- enjoy a working oven and feel like an absolute PRO for fixing it yourself!!!!

Just a replacement burner for my stove. No tools needed. Thank you for such a speedy delivery

I unplugged the stove for precautionary reasons.
I then removed the two screws holding element in place with the correct nutdriver.
I then carefully pulled out the element and pulled the two female spade connectors off.
I then compared to new element and plugged the new element in.
Finally I screwed in the new element and tested the oven.
It worked again!! I would recommend running the oven for a bit before placing anything in to bake. this allows burn off of stuff on the new element.

First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.

It was a little difficult by my self an extra hand would of made it much easier.I unscrewed the screws pulled the wires from the back of the oven which took a few minutes.I am not great at fixing things but once I got the old one out it went smoother than I expected.it took about 25-30 minutes with an extra hand could have made it 10 minutes.not bad over all for me.did I mention not very handy.did stun the wife that I fixed it on my own.thanks Bill