CC35111ACV Crosley Range - Instructions

I ordered the part and it came in within 2 days from fedex! Great timing. It took me all of 10 minutes to fix the coil at the bottom of the oven. Fixed the problem and had plenty of time to cook dinner before my husband came home!!
GREAT SERVICE AT THIS SITE! They knew the right part! And the instructions are very simple.

Thank you

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) One of the wires came off before i was able to pull the element out far enough. I then had to take the back off (2 screws) The total repair took about 5 minutes

used the supplied parts...very easy. The parts were exact replacements.

First off, I ordered the part to be delivered 2-3 business days. I ordered this online on Sunday, so I figured it wouldn't show up until at the earliest on Thursday. We got it on Tuesday. Fantastic. Once I got it I pulled the range out and unplugged it. Next I removed the two screws holding the old element in place with a phillips screw driver. Pulling the old element out carefully I removed the two wires from either end. Next I attached the wired to the new element and screwed in place. Fast and easy! Plugged the range back in and we were cooking.

Your site really helped out alot. Job was farily easy and now we have heat. Difficult part was reaching the wires in the back. Thanks again! TZak

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.

slid out the range removed the old replaced it with the new. very easy repair

Took out two screws in the back of the oven that held in the bake element. Pulled the element out of the back of the oven to expose the wires. Pulled the wires off the broken element and then reattached the wires to the new element, put it back into place. Reattached the screws. Done in less than five minutes.

My husband did it was really easy ,he turned the power off to the stove,took the back cover off the stove with a screwdriver and pulled the old one out,then he slipped the new one in connected the wires ,it took less than 15 minutes that simple.

First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.

Actually a very simple repair. Determined that the problem was a burned out bake element since broiler worked fine. Looked up part on-line...diagram on PartsSelect made this very easy.
Ordered part selecting normal shipping (part arrived in 3 days). Repair: 1) turned power off at the breaker box 2) removed baking shelves. 3) removed the two mounting screws holding old bake element in place 4) gently pulled the bake element out of the oven until about two inches of electrical wire were exposed. 5) removed the electrical clips from the old bake element. This required steady wiggle to get them off. 6) attached the electrical clips to appropriate ends of new element ensuring they are well seated 7) pushed electrical wires back into the oven and mounted the element using same two screws. Turning the power back on at the breaker, I then tested the repair. No problems noted...turned oven off and replaced the baking shelves. Baked homed made bread that evening.

I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.

I looked up the part from the parts diagram list and was easily able to order it. The part arrived quickly and I installed it.

Screwed in light bulb and glass protector