CC35111ACV Crosley Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mz from COLUMBIA, ME
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from GUSTON, KY
- Parts Used:
- WP74010750
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element in oven went out
Take out 2 screws. Unplug the old element, plug in the new one and put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETH from COUNCE, TN
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
burner receptacle failed (stove over 30 years old)
Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from BROWNVILLE, NY
- Parts Used:
- W11665456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
My original back leg broke because the floor is uneven. Had to pull it out several times.
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from ELKTON, VA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
My oven door seal had dried rotted
I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Aurora, CO
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
the lower baking element had burnt out, literally
Unscrewed two Phillips screws holding the element in the back of the oven, pulled out the element and the leads, disconnected the wires, removed element from oven and reversed the process to install new one. One most important and critical maneuver - the element is connected to the hot wire on the left side and the switch shuts off the element by disconnecting electrical flow to the neutral side of the power so its not enough to just have the oven turned off - makes one heck of a spark when the wire touches the stove panel when you pull the wire through the hole (220 at 60 amps).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AmyKuta from GARLAND, NE
- Parts Used:
- WP74010750
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Element caught on fire when oven was turned on. Burned off coating on element.
Turned off power to oven. Removed screws from each side of element. Removed connectors to disconnect old element. Connected new element to connectors. Replaced screws, then turned on power to oven. Turned on oven to heat. Easy install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TUONG from ALBANY, NY
- Parts Used:
- WP7403P255-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
selector switch not smooth and no heat on element
un-plug device from outlet for safety first and then remover all top panel after screws lower two side small screws. actually is not selector problem. It was burner switch problem for 6 inches element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from CAMAS, WA
- Parts Used:
- WP74010750
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
None at all.
Just took the old one out and put the new one in. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paulo from Cambridge Springs, PA
- Parts Used:
- WP12001560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our original surface element caught fire!
Old surface element was removed simply by pulling it out of the electrical contacts. The, the new one was inserted.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James H from Victor,, NY
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken Coil
Very easy to install with the advanced instructions you provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paola from High Bridge, NJ
- Parts Used:
- WP12001560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just plugged the burner in and it was good to go.
The burner wouldn't work. I just plugged in the new one and all was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heidi from Lakeland, FL
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element was broken(literally).
First, turn off the breaker to the range. Then just remove the 2 screws that hold the element at the back of the oven. Pull the wire connectors apart or push them off with a regular screwdriver. Instructions that I read said to make sure the wires don't fall back through the holes, but in our case the insulation held them in place. Reconnect the wire connectors to the new element and reattach with the screws. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from VASSAR, MI
- Parts Used:
- WP74010750
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking element went out on our cook stove.
It was easy finding the part on line and the part was delivered within three days. It only took about 10 minutes to change element. I was so pleased with the product, that I just changed a thermostat on my parents stove which was purchased through parts select and that was very easy to change also.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Delray Beach, FL
- Parts Used:
- WP74010750
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lower bake element burned out.
First off, I ordered the part to be delivered 2-3 business days. I ordered this online on Sunday, so I figured it wouldn't show up until at the earliest on Thursday. We got it on Tuesday. Fantastic. Once I got it I pulled the range out and unplugged it. Next I removed the two screws holding the old element in place with a phillips screw driver. Pulling the old element out carefully I removed the two wires from either end. Next I attached the wired to the new element and screwed in place. Fast and easy! Plugged the range back in and we were cooking.
Was this instruction helpful to you?
Thank you for voting!