CC3520SRW Crosley Range - Instructions

first I removed the 2 screws, I then pulled the element out., accidently lost one of the wire in the insulation and had to take the back panel off which was 8 screws. Probably doubled my time. I received my part in 4 days thanks to good service and FedX It arrived the day before Thanksgiving. Just in time, Thank You All.

I Unscrewed the attachment plates located at the back of the over. Pulled the element out so that I could "unhook" the prongs. Replaced the new element by clipping on the prong attachement (you will see where the electrical wires are). Screwed the plates back on and Vola! I'm baking again.

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

Turned off power circuit to oven. Removed old element by unscrewing two nuts attaching unit to back of oven. Used pliers to help release electrical connections at both ends of element. Re-attached connections to new unit. Screwed nuts back into place. Turned power back on and cooked dinner. Total time for repair was less than 5 minutes.

I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.

used the supplied parts...very easy. The parts were exact replacements.

Broken part was already removed, so I used the screw from the broken support and installed the new support. Very simple, easy, and painless.

Called repairman, he never called back for a week. Gave up and found your website, ordered the part. You said it would take 3-5 business days. You lied, it was there the next day. Taking old element out starts with shutting off the juice. Remove trays, pans, etc. Unscrew two screws, pull out elements ends, unclip from wires, reverse the process with new one. You need a light to do this.

removed drawer from track replaced supports on track and one on the drawer.

I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.

the new elements were super easy to replace. the old ones just pulled out and the new ones easily pushed in. the top one was a little more difficult only because it had brackets that had to be slid of and then slid onto the new one.

First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.

Removed old element (two screws) unclipped two wires. Clipped the two wires to the new element (one at each end), reinserted new element, replaced the two screws. Done. Oh, flipped the circuit breaker back on:-)

I shut the breaker off at the main power box.
In the oven, I loosened two screws to remove the old element (parts now, after the burn-out). I pulled the old element out of the back wall of the oven to expose the wire connections. I detached the simple sliding wire connectors. Done with removal. I waited for the new element to arrive (one week). Installed easily. Turned on the breaker and baked a few potatoes. Very simple.

This was a snap. It took me longer to find the right part number than it did to make the repair. After securing power to the oven, I removed the racks. I then unscrewed the element supports and pulled the element out slightly to expose the connectors. Using a pliers I removed the connector from each side of the element. At this point, I should have placed a piece of electrical tape to prevent the connector leads from slipping back into the body of the oven. Instead, I fished them out with a tweezer, and slid the connectors back onto each side of the element. I then screwed in the elements supports, replaced the oven racks, and restored the power. It literally took less than 10 minutes.