ART6121E-P1143812NE Amana Range - Instructions

I was surprised when I was able to find that the (10 year old) parts for one of the drawer slides of my stove were still available. However, I was disappointed that the small bolt that I ordered did not come with a nut. I was lucky to find one in a collection of nuts in my workshop, and so was able to fix the slide. However, I suggest that if you supply someone with a bolt, that you include the nut that is necessary to make it work.

first removed 3 screws in front of the range then lift up the top glass and removed 1 screw that is holding the element and then disconnect the wires that are connect on the element then put the new element on place and wired it test it and works good

had to slide the range out from the wall and pull the electrical plug, then using a nut driver ,I removed 9 screws from the back panel and removed the back panel to expose the bake element wiring, had to remove the three wires connecting the power cord to the range terminals a/c the back panel would not fully come off with these wires connected. i then pulled the 2 stake eyes from the element, unscrewed the 2 screws
securing the bake element from inside the stove and removed the element, re-installed the new element and screwed into place, attached the
stake eyes on the rear of the element and re-attached the power cord, put the back cover back on and plugged the range in., tested and the range functioned as intended.

It was simple. I flipped the circuit breaker just in case, and then unscrewed the bracket for the old heatng element. Disconnected the two plugs, connected the plugs for the new element, and screwed the new bracket back in.
The saleslady assured me when I was purchasing it from PartSelect that it was pretty easy. That gave me the confidence, and she was telling the truth. I will purchase again from Part Select....although I hope I won't have to do so for a while.

I turned off the breaker and unscrewed the element. Removed the plug connection and once I got the correct part, we plugged it in, screwed it back into the oven wall and done! I am a single female and was able to replace the heating element in a short amount of time with assistance from my 16 year old son!! I was very surprised at how easy it was to repair. The key is to get the correct part the 1st time!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Plug the wires onto the new bake element and re-screw back into place.

removed 2 screws holding top in place witch gave me ac access to none working part. removed 5 screws witch let me remove part, reversed order to reinstall part, very easy
Donald Carpenter

First, I unplugged the power cord from the receptacle. I then removed two philiphead screws that hold the element in place. I the pulled the element out about an inch and a half . I then disconnected the the two wires from the element. The I connected the replacement element and resecured it with the two mounting screws. I assured everything was correct and then I plugged in the power cord and turned the oven on low heat to give it a test. Everything workout just great. The part was just what I needed.

Removed two screws securing heating element. Removed broken element and disconnected wires. Removed back panel of oven, unplugged from outlet, installed new element, attaching 2 screws. From back side of oven reattached 2 wires, replaced back panel and plugged in. Pretty simple!

Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You

Very simple fix. I pulled the stove away from the wall and unplugged from outlet. Open the oven door and remove the oven racks. I used a phillips screw driver to remove the 2 screws holding the element and then pulled out. There were 2 wires attached to the element, those just pull off. Just reverse the process with the new element and you are good to go.

Removed 3 screws, lifted the top control panel. Adapted new plastic end panel and replaced new end cap an refastened with original screws.

1. removed the screws that held the caps.
2. Moved the stove away from the wall.
3. Unplugged the power cord, for safety.
4. Removed the caps.
5. Install the new caps.
6. Plug the power cord in.
7. Place stove back in positon against the wall.

Switch off the breaker or unplug.
The screws were in tight so make sure your philips bite is new so you do not strip.
Pulled the element out and held the wires in place with a clothes pin so not to slip back in the stove.
Connect and cooked up pizza for dinner.
Very easy

Removed two screws-put burner in-pit screws back in! Turned over on and it worked!!!