Models > AGR5844VDB0 > Instructions

AGR5844VDB0 Amana Range - Instructions

Jump to:

All Instructions for the AGR5844VDB0

Customer:: carl from peoria, IL
Parts Used:: WP9758079
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Igniter went out

Pulled shelves out removed bottom plate of oven remove heat shield cover removed screws had to remove bottom drawer disconnect wire from bottom of igniter and remove from top side . Replaced by reversing steps.

Was this instruction helpful to you?

Customer:: David from Mauldin, SC
Parts Used:: WP8053334
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Rear drawer slide was broken.

Undid one screw. Removed the broken slide. Replaced with new slide an fastened with the existing screw. Problem solved.

Was this instruction helpful to you?

Customer:: Lee from Saint James, NY
Parts Used:: WPW10107820
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Gas range would not go into self cleaning mode. When pushing the self clean button, would get three beeps!

The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job. If your handy at all, it should not be a problem.

Was this instruction helpful to you?

Customer:: Dave from Titusville, FL
Parts Used:: WPW10181986
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

Was this instruction helpful to you?

Customer:: Dennis from Ft Myers, FL
Parts Used:: WPW10118454, WP8523175
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Glass door front fell out during cleaning and shattered

Install bottom door trim first...Remove upper door handle and set new glass door front piece in place and re install upper door handle and tighten all screws...Looks great

Was this instruction helpful to you?

Customer:: Thaddeus from Washington, DC
Parts Used:: WPW10118454
Difficulty Level:: Difficult
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

broken outer range door glass

Using 4 strips of duct tape was useful,in holding the glass to the door.

Was this instruction helpful to you?

Customer:: Charles from Fairfield Bay, AR
Parts Used:: WPW10107820
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Could not get self cleaning oven to engage

Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]

Was this instruction helpful to you?

Customer:: Paul from Adamsville, TN
Parts Used:: WP8523166
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Side trim broke

take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.

Was this instruction helpful to you?

Customer:: Grant from Alexandria, VA
Parts Used:: 8009
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Light bulb failure

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Was this instruction helpful to you?

Customer:: Philip from New York, NY
Parts Used:: WP9758079
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Screw drivers

Bake would not work all the time

The bake part of the oven was not igniting all the time . I checked the website and they don't list the igniter separately from the burner tube. This part is the exact fit for the igniter. There is no need to buy the whole kit if the igniter is all you need. it will fit right on the burner tube with no modification at all. Part number PS897264 is the igniter and burner tube. Part number PS898618 is just the ignitor.

Was this instruction helpful to you?

Customer:: Richard from Wooster, OH
Parts Used:: WPW10181986
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Stove kept turning off

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

Was this instruction helpful to you?

Customer:: Doris from Brookline, MA
Parts Used:: WPW10256908, WP3195097
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

When I originally purchased my stove, there was a large paper describing stove features. It was glued on and when I removed it, it left glue which I could not remove. I s hould have returned stove, but I didn't.

So, after several years of it bothering me, I decided to replace the oven panel. I ordered it one day and it arrived the very next day. It was an easy job to replace. Just remove two screws in back and replace the panel. While I was at it I also replaced the racks. Now I have a brand new oven,thanks to PartsSelect!

Was this instruction helpful to you?

Customer:: Ken from Las Cruces, NM
Parts Used:: WPW10181986
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven shutting off after temp reached 350

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

Was this instruction helpful to you?

Customer:: karen from Thornton, CO
Parts Used:: WP8053334
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Broken drawer glide

Used a phillips head screwdriver to remove the single screw holding the part in place and put the new one on. Finding the part on this site was a breeze and it arrived quickly. A first rate experience all around.

Was this instruction helpful to you?

Customer:: Gregory from Arlington, VA
Parts Used:: WP9758079
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven has not heat

Open oven door and remove racks. Remove 2 screws at back of oven floor and remove bottom plate. Unscrew screws that hold flame defuser. Remove defuser. Remove screws that hold bake igniter and flame tube. Unplug wire to bake igniter. Remove screws to bake igniter. Replace old igniter with new igniter. Replace screws and wire to igniter. Replace flame defuser and put screws back. Put bottom plate back into oven. Replace 2 screws at back. Replace racks. close door and test by setting thermostat to some temperature and verify that oven works.

Was this instruction helpful to you?

All Instructions for the AGR5844VDB0