AGR5844VDB0 Amana Range - Instructions

Lifted the top disconnected the old valve and replaced with a new one.I believe the valve should have been shipped with two gaskets,. One for the bottom and another for the top. I reused the old one on the top with no problem but would have preferred a new one.

Removed old trim kit and handle installed new parts but was having problems with glass fitting between handle and bottom bracket there was a gap between glass and handle when installed fist time after disassembling again I found that the door frame it self had to be tapped back into alignment to be square but once the adjustments were made the installation was a breeze

Clean off all broken glass and wipe down the debree,figure what side the glass goes then unscewed the base then the sides then add gorrilla glue on the edges to help set the glass in place had some hold it the screw th center bottom in first then got the sides in place with the bottom rack then screw it all back in to place making sure the side and top were in place right that was it.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

The first thing you need to do is remove the racks from your oven.

Then look around at the back of your oven for the screws that hold the bottom pan down.

Remove those screws and remove the pan. Some need to slide back and then come up others will just pull up.

Remove the heat shield that is over the burner.

Remove the bottom drawer of your oven.

Now you should be able to see the igniter that sits on an angle by the burner tubes with a couple of wires coming out of it.

Removing the screws that hold the igniter is probably the most difficult part with some ovens. Sometimes it is easier to remove the whole bracket that holds the igniter and then remove and replace the igniter out of the oven.

The wires for the igniter will go to a Molex plug. Follow the wires and undo the plug. On many units it will be below the oven in the drawer opening at the top back. You will need to lay flat on the floor and reach back in to do this.

Once you have the old igniter out then you can carefully install the new one.

Check to make sure that you can feed the Molex plug and wires down through to the bottom before fastening the igniter.

Once the igniter is secured and the plug is connected, you can then replace the other parts in the reverse order that they came out.

all I did was replace the igniter and that fixed my problem simple to do.

Replaced bake igniter only as recommended by others, no need to buy the whole unit. The bottom screw is difficult to access, use a 1/4 inch socket set with 8 mm socket. Advice to remove bottom storage drawer to make sure wire is connected to the igniter. So far it works fine.

Removed door per instructions in manual. Removed racks and storage drawer per manual. Removed two phillips head screws holding bottom pan and removed pan. Removed two phillips head screws holding igniter tube (#12) and withdrew tube from the cavity. Removed two phillips head screws holding igniter and bracket to the tube. Unplugged elcetrical connection to igniter and installed new igniter in reverse order. Too bad the igniter wasn't the problem.

I remove bottom trim which is held on by 3 screws and try to install new bottom trim, did not work well. I then remove yop handle assem. Then the door glass which you need to clean after. Then install the new bottom trim then insert the glass into the new bottom strip using masking tape to hold the glass and side strips in place prior to installing the the top handle piece which is held on by two screws. Not a hard job to do.

We took the door off and took it and the side panels to the local dealer and he put them on for us - for anyone needing to replace the side panels on the over, be aware they slide under the glass front -not over it like we tried to do. We thought, though, that we were going to have a buy a new stove but for a little over $70. 00 We got the parts, had them installed and saved over $800 on a new stove - well worth the effort.

Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine. Of course unplug stove before you start !

just replaced the broken glides with the new ones.

oven would not light but broiler and range top would. removed oven racks. removed 2 finger tight screws on oven pan floor and pulled up oven floor. also removed storage drawer under oven- also 2 screws. now your oven should look like the inside of your gas grill. removed 2 more screws on burner plate and removed plate. unplugged igniter and 2 screws holding igniter. replaced igniter and put together in reverse order. oven now works perfectly

First make sure it is the gas valve not the ignitor. If the clicking sound still happens then the ignitor is fine, no clicking means ignitor may be broke and try to fix that first because it is cheaper. For us I knew it was the valve because the ignitor still clicked and the broil and top elements still worked. After the part arrived I turned off the gas and pulled the power to the oven. Disassembled all the components taking pictures along the way to remember what it looked like to go back together. Installed the new valve and use yellow gas tephlon tape at the seals. Put components back in reverse order. Run the top elements first to get gas in all the gas lines and remove the air. At this point the oven bakes again.

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.