ACS3350AW0 Amana Range - Instructions

The repair was fairly simple. The hardest part was figuring out the best way to get access to the part. Basically just had to remove the cover at the bottom of the oven then remove the shield that was directing the heat that comes off of the burner. Once I had access to that, I could see the ignitor. To get access to the plug in section, I had to take out the bottom drawer for pots and pans, then remove the piece above that to get access to the place that the ignitor plugs into. Unfortunately the wires were too short, but so were the ones that were on the current ignitor so I used the extension from the existing ignitor and cut off the plug of the new one to attach the extension. Once that was done, just reinstalled the ignitor and we reversed the process. The new one works incredibly well. Instead of waiting several minutes for the oven to start heating up, it heats up instantly. What a relief...much cheaper than buying a brand new stove. This one works great now!! Thank you parts select!!

I ordered the part and it was at my door in 2 days. I ordered the part on Wednesday thinking I would install it on the weekend after next. The part showed up on Friday. That was amazing considering I didn't sellect expeidited delivery. I didn't have a manual and have never tried this before so grade my attempt on a curve please. I started by unscrewing the screws closest to the hinge but quickly migrated to the entire face of the range. Pulled the range out and started unscrewing the screws on the side, and then the back. Figuring nothing was coming off and I still couldn't get to the hinge I stopped and regrouped. That's when my wife asked if she could help. I guess I looked distressed. By this time I had removed the drawer and had the range on it's back in the middle of the kitchen with little bowls of screws everywhere. My wife picked up the new hinge and looked it over. Then she started playing with the old hinge which was loose, but I couldn't get it out. She realized that you can remove the old hinge and install the new hinge without taking the whole thing apart. Where was she 30 minutes ago? The hinges came out and the new ones went it in about 10 minutes. It took me another 20 minutes to put back all of the screws I had taken off unnecessarily. Sometimes use your brains instead of a screwdriver. I have the best wife ever!

I had changed the broiler igniter several years ago, but it had "burned out". The only thing that slowed me down on this repair was that the igniter was glowing brightly, but the oven would still not ignite. Others have written that it's best to try a new igniter FIRST. That indeed was the solution.

One "trick" that I did not find in other posts was how to get to the plug on the end of the igniter - so here's how.

First, open the oven, remove all racks and the bottom cover. Remove the nut holding the heat deflector in place and remove the heat deflector. Then remove the three screws holding the igniter in place.

Second, pull out the bottom drawer of the ove and remove it. At the very back there is a sheet metal cover held in place by two additional screws; remove them to rermove the sheet metal cover - this will allow access to the plug on the other end of the igniter. Unplug the igniter.

Third, feed the plug end of the new igniter from inside of the oven to the underside. Plug it in, reattach the sheet metal cover, reinstall the drawer, screw in the new igniter and put the heat deflector back in place.

Note of caution: be careful handling the igniter - it's fragile and easily broken.

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased

I bought the part and replaced it.

I pulled the ckt breaker, removed the oven drawer and disconnected the igniter. I opened the oven door and unscrewed the igniter holding bracket and removed the bracket and igniter. I broke the old igniter element when removing it from the bracket. When installing the new igniter in the holding bracket I broke the ceramic element. REALLY BE CAREFUL. Ordered a new igniter, very carefully installed it in the bracket, then rversed the removal process. It's not hard, you just have to be careful

very simple repair, the oven had the issue about ten years ago, just removed drawer ,removed two screws holding cover plate unhooked power and disconected plug. removed element screws and pulled out old element from holder and inserted new one. re attatched element holder, cover plate, and put drawer back in. works great !!!
My parts wrere shipped promptly and arraived in great condition, stove looks and works like new again

found igniter not working, pulled up on door and it came off, lifted up bottom of oven and pulled out, removed wing nut on deflector to access igniter, removed igniter retaining bolts, unplugged connector, be careful not to let connector slip back in stove, and reverse process to install new igniter,, all took about twenty minutes, easy repair,

First, I removed the oven door (two screws and pulled it off the hinges) and placed it out of the way. Then I removed the baking racks and bottom cover over the heating element this exposed the heating element, easily removed (two screws). I unplugged the old element, plugged the new element in, and put all the stuff back and the put the door back on. Next was the fun part. . . Had to get the wife to turn on the oven (very complicated touch pad - not made for a man to understand), and shazamm the oven came on! Now I can have some of those great homemade biscuits again!

We removed the oven protective shield, took out the broken glass (very carefully) and replaced it with the part shipped. Then, we replaced the protective shield and it was done.

Removed burner with attached igniter assembly by raising forward legs from slots and pulling unit from rear support. Note: this is contrary to instruction #1 on installation instructions. Then followed the remaining instuctions 2 - 7 as written. Everything worked as planned.

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

Removed the oven racks for room to work.
Removed a protective cover (slide forward, lift up).
Remove winged cover plate.
See igniter assembly.
Remove 2 or 3 holding screws (I don't want to go in and count them - it's obvious - they are clearly in view - get a good screw-driver seating - they come out easily).
The igniter assembly is then loose and ready to com out.
Remove the stove drawer to get at the access plate at the rear - comes off easily(the wires to the igniter were then clearly identifiable).
Release the wire plug - I marked one side with a sharpy - polarity of fit, not voltage.
Gently feed the igniter assembly out the bottom using the wires.
Remove the igniter from the shroud (may have to pul it apart a little - it's tight - it does come out easily after prying the shroud a little - mark a side with a sharpy - for mechanical orientation.
The part number should be on the igniter.
I did not bother matching the part number.
Just matched the stove brand and model.
The parts diagram provided by PartSelect was invaluable.
I put an ac meter up the holes of the plug (stove side, of course) turned on the stove to see the meter measure 115vac - assurance that the igniter was bad and not anything else.
Just reverse the removal process.
Just takes a little time and patience.
Very very doable.
Good luck.

Removed oven grills and top of burner pan. This exposed the igniter. Removed 3 phillips head screws from igniter bracket. Slid old igniter out the back end. Removed utility drawer. Removed two screws from back pan covering igniter plug-in. Unplugged igniter, removed from range. Handling of igniter is tricky..do not touch black end. Slide new igniter into the bracket, feed wire with connector through hole in back (where igniter was removed from), install the three screws for the bracket (your new igniter is now secure), from the bottom, plug in the new connector it only goes on one way. Re-install pan with two screws. Put utility drawer back in..job is complete!!

First turned off power to oven, Took burner out by lifting up and pulling out, then pulled out wires attached to the oven and igniter, removed two wire nuts and disconnected the wires then removed burner assembly from oven. With screwdriver and nut driver removed old igniter from housing and put new one in place, tightened up screws carried back to oven reattached wires with wirenuts and feed wires back into oven, then put burner back carefully silding igniter into hole in back of oven. Turned power back on to oven and worked nice. Took all of 15 mins to complete.