ARTC7522E-P1143817NE Amana Range - Instructions

Removed top of stove replaced heating element ,piece of cake.

The key to this repair was making sure I typed in the correct model number and serial number so that I got the correct part. I had read here that a couple of folks had received the wrong temperature sensor (i.e. it had the male plug instead of the female plug). Unfortunately I had to call the local appliance repair guy as the plug could not be accessed from the interior of the oven. It was easy to remove the 2 screws that held it in place but I could not pull enough of the wire out to access the plug. The local repair guy pulled to oven out and removed the back in order to unpluy the bad sensor and plug in the new one. It was actually kind of nice that he came as he used a digital thermometer to cycle the oven through a couple of warm ups to see if it was actually working correctly. It worked fine and my wife was happy again. The $75 I spent on the repairman was darn well worth it. "Happy wife = happy life!"

Removed the old sensor which is held into the upper right of the back of the oven by removing the two screws and pulling the sensor out. Then disconnected the sensor from its connector. Replace the old with the new by simply clicking it into the connector. Then pushed the wire back into the oven wall and screwed the two screws back in. The whole job took about one minute to do after evaluating the process. While it was not necessary to remove the door, I did (which was very easy) and ended up cleaning the glass inside and out. All in all, a complete success. Oven working as new.

The repair was simple, two screws and plug in and it was done.

The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.

1. waited unsuccessfully for heat (one hour) 2. realized the bottom element wasn't working (one minute) 3. found part on-line from pictures (five minutes) 4. ordered part (one minute) 5. received part (36 hours) 6. installed part (five minutes) 7. "THAT'S how you fix the oven" look to husband (1-2 years)

Move stove away from wall to allow working on back of stove. Unplug stove. Remove metal cover from top rear of stove. Pull control knob off of control (front of stove) Remove 2 screws holding infinite control in place (front of stove) Replacement control not identical to original control, having more terminal lugs and different physical arrangement. I used the terminal letters as a guide for placement of wires. The letters were not exactly the same, but close enough. Re-attach control to stove with 2 screws. Re-attach back metal panel to stove. Shaft on replacement control is smaller diameter and different shape from original, so I removed ribs from inside of control knob hole and then squirted a small amount of hot glue into the hole. Smearing a small amount of cooking oil onto shaft of replacent control I then slid the control knob onto the control shaft, holding it in place until the glue cooled and set. Plug stove back in, and return stove to its position next to the wall.

Took off the back panel, unplugged the power cord, and tested the switch with an ohm meter. Found it open and ordered new switch. Replaced it easily and now have both elements working as required.

This particular Amana electric range has a "eye" that can serve as the heat source for a small or large pan simply by using the rocker switch to "flip" between "large" or "small." This switch broke. I found Partselect.com, found the part, ordered on Saturday night and received it on Tuesday afternoon. 1) Shut off power to the range at the breaker box. 2) Used a small flat-head srewdriver to pop the old rocker switch from the appliance. 3) Used a set of locking pliers to hold the wires in place as I disconnected the old switch from it's connections using a set of needle-nose pliers. (It was a plug-in style switch). 4) Plugged in the new switch. 5)Released the wires from the locing pliers. 6) Popped the new switch into the range's cabinet. 7) Flipped the breaker to "On". WORKS Perfectly

Unscrewed 2 screws holding the bracket on the back of the stove and disconnected the wires from the two clips. Removed back element, connected new elements & replaced screws to back inside wall of oven. Works like brand new!!

Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.

Pulled range away from wall and unplugged it. Pulled smoothtop out a bit to clear retaining clips. Swung top up and unplugged the cable going to top. Removed top hinge so top could be removed. Put top upside down on a table to work on. Removed wires from bad burner and then removed screws holding the burner in place. Replaced bad burner with new one and reversed the previous steps. Range worked like new. PartSelect service was great, received the part in one day.

turn the power off first, remove knobs, removed burners,disconnected wire from igniter,raise the top of the stove,re rmoved wire from the door lock removed two screws remove the door lock itself, then put all back on in same order as I remove. Main thing to remember is to writeyour colors of the wire down so you know where to replace them.

Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.