FDU2482B (P1130613N B) Amana Range - Instructions

After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.

Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.

Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold the socket, etc.

Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!

Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.

It was so easy to order a new one from your company. And it arrived in less than a week! I slipped it into the electric outlet and it worked perfectly. THANKS. Wanda Major

It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.

The four kits arrived, use of a pliers and shink wrap and side cutters...strip wires, twist wires connect wire ties, shrink wrap...little fire, plug the elements...done...four in about ten minutes...Instructions in each package...no problem...very easy...saved twice the money or more...Thanks for the parts...recommend this site purchase...parts arrived very timely...J. Iriwn

I lifted the stove top and cut the two wire connected to the block. Attached the new wire connectors, new block and checked to make sure it was working. The part that took the longest was getting the screw out of the mounting brracked(it was corroded on). I sprayed some WD40 and waited 5 minuts, it came loose. Then i mounted the new bracket and installed the burner. double checked everything and lowered the top. Done

A frind (my husband has ALZ> came over before I ordered the part lookt at it took it out and told me what to do. I ordered the part and got it in 3 day's Wonderfull.My friend came the next day and put it back in. I cleaned the oven the next day and I am back in action THank you so much for the great service P v. d. B

burner was shorting out replaced part works great

Cut off power to my range at the circuit breaker. Removed the 2 screws from the original element, pulled the element out about 4 inches to expose the wires to see the connections. (I put clothes pins on the wires to keep the wires from possibly sliding back into the holes in the oven.). Pulled the connections apart carefully, removed the old element, plugged in the new one, slid the wires back in the holes, replaced the 2 screws & was done! I did this by myself before my husband got home ... very easy! And I was thrilled to have my oven back!

loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.

I removed the entire burner assembly to avoid having to turn things off at the breaker - the whole assembly can be removed completely from the stove I had. Once it was out and disassembled, the toughest part was putting the new wires into the new block correctly. Once that was done, I had to select the right mounting bracket - there were 2 in the kit. Easy, just attention to detail. The rest of the instructions were easy to follow, re-doing the wires. The re-assembly was trivial, and it worked first time!

After carefully inspecting existing burner receptacles, I unscrewed them, raised and propped stove top. Determined which bracket to use from new kit and proceeded to cut and strip wires, twist ends together with supplied ceramic caps and heated shrink wrap on that junction. Works great. BTW got parts in 2 days in great shape and good directions.