FDU2482B (P1130613N B) Amana Range - Instructions

I took the old wires and plug off and replaced it with the new block it works fine

Someone did the repair for me.

I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.

Time was do to the fact that I replaced two elements! I turned off the power to the braker box, unplugged the stove and removed the screw holding the element plug in, removed the part, and cut the wires where they were clean looking (not damaged by smoke or the arch) I then stripped the wire and took the new part and twisted the parts together with the caps and then put the heat shrink on and used the blow dryer on them, attached the part to the bracket and screwed it to the hood of the stove plugged the burner in, plugged in the oven and turned on the power tested it worked, did the same for the next burner and yes mind you I am a woman it was very easy to do.

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predrilled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

Really easy!! Cut off Breaker so the Range had no power. Use phillips head screwdriver, remove the two screws holding the bake element in. Remove connectors from element. I put (heat shrink) wrap around the female connectors then attached them to the element, heated the shrink wrap, replaced the screws and cut on the breaker / power. Turned on the oven (350) to "bake" off the oil film off of the element. (Element will smoke / smell for a few minutes).

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

Removed the original burner element sockets and replaced with parts provided in kit. Instructions were simple and easy to follow, problem completely solved in 20 mins!

Cut power. Removed four attaching screws and raised stove top. Cut two wires of existing burner plug. Used existing plug to select correct plug configuration from parts in kit. Attached new plug and wires to wiring harness using connectors and heat-shrink tubing supplied with kit. Used hair dryer to shrink tubing on connectors. Closed up stove. Restored power. Burner now functional.

The directions were very clear. I removed the heating element, detached the plug-in block by unscrewing the screw, then cut the wires about 3 inches from the block. I put the shrink-wrap collars around the wires leading to the new block, then attached the wires to the cut ends of the wires leading to the back of the stove, using the connectors provided in the kit. I couldn't get the collars to shrink as much as shown in the picture. I attached the new block to the stove top using the screw, plugged in the heating element, and it worked!
So the instructions were good, and the heating element is now working. The only problem was the heat shrink collars that go around the connectors: I couldn't get them to shrink much, but that doesn't seem to matter.

First I removed the one screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

First I lifted the cooktop out of the countertop & removed the screws so I could access under the burners.Then I cut the wires for the old plug-in block & then stripped the wires.Next I connected the new wires with the wire nuts & then used a lighter to shrink wrap the wire nuts.Then I screwed in the new block & re-installed the screws for the cooktop.I put in the new burner & it worked just like new.

Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube over the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!

All the necessary parts came in the repair kit, delivery was timely. Very easy project.

First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They work very well now.

Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.