ARG7200W (P1143316N W) Amana Range - Instructions

Instructions with parts are minimal. Looked at exploded drawing and read other installation descriptions on site. From the read I knew it was easier than it looked. Opened oven door. Unscrewed screws about 1/3 of the way up on both sides on inside face of door; these are the only thing attaching the hinges to the door. (Save all the screws you remove - they make work better than the ones with the parts.) The door can now be pulled off the range. I pulled the broken part out of the right side with pliers. Remove the screws below and about 8" up from the hinge on each side. When this is done you can pull the hinge out from the slot from the front. Open the new hinges up and they will slip through these same openings and position them as the ones you removed were positioned. Replace the screws. On the parts I received the lower screw holes on the hinge were not tapped. The original screws worked a bit like self-tapping ones. If you lose any parts or need to get to the hinge from the back you can take out the drawer.

I took out the oven racks. There are 2 cross head screws and 1 screw with a hex head holding the igniter. Pulling out the igniter carefully and the wire nuts also came out. Replaced the wires using the existing wirenuts and slid the igniter into place. Replaced the 3 screws and DONE. Wish the igniters were a little cheaper as this is the third one to go weak. The new one draws about 3.2 amps while the old one only drew 2.85Amps, not enough to open the gas valve. Oven works Fine now. Thanks parts select for the rapid delivery.

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

Removed oven door. Removed three screws on ignitor holding bracket. Pulled out the range from the wall and reached underneath to access the wire nuts on the wires. Removed old ignitor and replaced with new one. Reconnected wires and then and replaced bracket and that's it. Works great now.

i had to remove quite a lot of screws in the bottom "pan" of the over to get to the igniter wiring. once it was apart, it was easy to see how to disconnect and reconnect the new igniter. the trickiest part is to put the igniter into the metal sheeted housing before you try to thread the wiring through to the plug at the back of the stove. overall, this is an easy rip out and replace process.

I removed all 4 burners 2 screws holding each,replaced the ignition module,wire for wire,reassembled after cleaning the stovetop.I,m my wife's hero.

Symptoms were sign of bad ignitor based on Goggle searches. Removed screws holding burner and ignitor to range. Disconnected ignitor at green connector below oven with lower drawer removed. Then removed burner and old ignitor. Reinstalled burner and then new ignitor being sure burner was still seated on gas outlet. (Note-burner removal may not be necessary) Replaced two screws attaching ignitor to oven wall and two screws attaching burner to floor of oven. Oven works perfectly now.

I replaced the Oven Igniter. With a ohmn meter I checked the resistance on the Igniter and there was nothing there. I figured the module had to see some kind of resistance to turn the gas on. The Oven now works after replacing the Oven Igniter, but the Broiler still will not light. I will check the resistance on the Broiler Igniter and see what is going on there.
The Igniter can be checked from the back by removing the back cover panels. The two igniter wires come out through the back of the oven and have heat resistant covering on them. They run into a plastic plug and can be accessed at this point to check the resistance.
To remove the Oven Igniter, remove the oven racks, the bottom panels which are held on by screws. The Oven Igniter is attached to the gas rail which is attached to the underside of 2nd panel by two wing nuts.

Took bottom oven pan off accessed through oven storage drawer.Removed a few screws holding the igniter bracket,removed igniter from its holder(Be really,really careful doing this procedure because the igniter tip is verrrrry fragile,ask me how I know)Put it all back together and Voila,it works!This is so easy a job a caveman can do it! Good luck!

1. Removed drawer
2.Removed back panel (2 screws).
3. Disconnected power line from old igniter
4. Removed 3 screws holding old igniter.
5. Replaced with new igniter.
Works like new.

Replaced the existing ignitor by removing the bottom drip pan/gas line/ignitor (apprimately 18 screws), unscrewing the wire nuts, removing the old ignitor, connecting the wires to the new ignitor, and reinstalling the drip pan/gas line/ignitor (18 screws).

Replacing the igniter itself was a simple matter a few screws holding its housing and then plugging the new one into the connector. Difficulty came trying to figure out how to access the igniter. Disassembling the floor of the oven was a dead end involving many screws. Pulling the unit out from the wall was a big job and another failure. The problem was solved with the removal of the drawer. Underneath, in the rear was a sheet metal plate held by 2 screws. Behind that hung the igniter connection. Voila! Job done.

I went ahead with the repair after reading how easy it was. I located the wires which were spliced, held together with wire nuts and wrapped in black insulation tape which did not feel right. Not realizing that these were ceramic heat resistant wire nuts and not wanting to cut the connector off the new ignitor I tried in vain to find a way to disconnect the original from it's source. In vain I searched for a way to reach where it plugged in. Looking for diagrams on line I came across one mention of: when you can't reach where to unplug the connector splice the wires using the heat resistant wire nuts. Encouraged I did that without the black insulation tape and then tried to slide the ignitor into the protective housing. The filament broke! I was devastated. Out $50.00 plus ego deflated I called PartSelect and bless their soul they sent me a new one under warranty. I didn't even have to ask for it. Their turn around time was the same as before and within two days not counting the weekend the oven lit like a Christmas candle. Thanks to all before me who shared their experience. Curious though why no one mentioned the splicing method.

PriceSelect was the best. Special thanks to them.