ARG7600LL-P1143345NLL Amana Range - Instructions

For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.

Followed Instructions with part. Easy Install. However the problem not solved. I believe Oven Control defective (Worn Out). Replacement May not be available. Still looking. Thank You. RJC

The repair was fairly simple. The hardest part was figuring out the best way to get access to the part. Basically just had to remove the cover at the bottom of the oven then remove the shield that was directing the heat that comes off of the burner. Once I had access to that, I could see the ignitor. To get access to the plug in section, I had to take out the bottom drawer for pots and pans, then remove the piece above that to get access to the place that the ignitor plugs into. Unfortunately the wires were too short, but so were the ones that were on the current ignitor so I used the extension from the existing ignitor and cut off the plug of the new one to attach the extension. Once that was done, just reinstalled the ignitor and we reversed the process. The new one works incredibly well. Instead of waiting several minutes for the oven to start heating up, it heats up instantly. What a relief...much cheaper than buying a brand new stove. This one works great now!! Thank you parts select!!

Removed burners and top cover to access ignition module.
Remove and replace module and reassemble stove.

Removed old ignightor and installed new one

Ceramic connectors were taken off the old igniter, pulled off old igniter and replaced in the same way the new igniter

Simple install - 6 -7 screws one nut. Once replaced oven worked good as new. Part shipped from PartSelect actually better than one installed by repairman 4 years ago - fit like an original part.

Thanks PartSelect.com

looked at and saw that ignitor was cracked,saw simple repair ahead. just needed the right part . Without part , select simple ,and easy selection, i might not have ever found the right part. as i said before finding the right part is 90 percent of the job and they made that an easy task .

of course if you want me to describe in detail, took out the pan saw the bad ignitor, removed 2 serews, disconnected 2 wire, the reassembled in the opposite direction. 30 minutes tops. I am sure this saved me at least 150 bucks for some "so called reparman" to do the same job, Most people do not realise that they have more education than most of these "repairmen". The only advantage these "repair people" have is acess to schematics and part numbers. Part select is a good start on putting this information in the hands of us average "idiots" as I am sure the repair folks call us when we pay 200 bucks for a 30 dollar job.

WEB research indicated that even though ignitor would glow, that it was likely faulty.
Turned off power at circuit breaker
Remove shelves and bottom plate from inside oven.
Unscrew deflector plate
Remove drawer under stove
Remove ignitor and unplug from connector
replace ignitor, plug in, reassemble stove.
Needed flashlight to see under stove.

It was Tuesday before thanksgiving, panic as there was a big bird looking for a hot stove,
unplug stove from its electrical supply
turn off gas, not necessary but sometimes it's good to be safe.
inside oven remove bottom splash cover "pull towards you and lift out, then remove flame pan, one nut in the center, remove and lift out flame pan.
The oven ignitor was to the left of the burner, with 3 philips screws one attached to buner and the other two to the back of the stove, remove all three.
The ignitor is now loose,
remove bottom drawer and behind is a plate attched to the back of the stove with two screw, the screws are facing you as you look in where the drawer was, remove screws and plate to access the plug attatching the ignitor to its power supply .
go back to the oven and remove ignitor.
install new, feed plug through back, and put it all back together.
"ignitor very delicate, handle with care"
I am also not the biggest of guys and it can be awkward getting in the drawer space as you need both hands to plug it back in, so tilting the stove back, keeping safety in your thoughts at all times, would be a must for most people.

My repairman told me it was probably the ignitor (even though the old one sitll glowed), but after weeks of waiting for his back-ordered part, I decided to try it myself - found it on PartSelect and had it 3 days later. Turned off the power to the oven. Slid out the 2 racks, and the cover below the racks. Unscrewed 1 nut and removed the V shaped metal plate that distributes the heat. Under that removed 3 screws that hold the ignitor clip in place and got the igniter out of the clip. I couldn't get to the plug on the other end of the ignitor until I took out the oven drawer and removed 2 screws holding a metal cover in place below the oven. Reversed the whole process being careful with the end of the new ignitor (I read it was fragile). The oven now heats up in 5 minutes and maintains temperature again!

We lived with the problem by using a long-reach butane torch lighter for three years after an appliance repairman told us the problem would be very costly to repair. Finally, we found the likely suspect when we happened onto PartSelect's website- the spark ignition module. The cost was just over $81 plus shipping. We ordered on Wednesday, it arrived on Friday by FedEx, and I installed it on Saturday morning. All the parts were included, the instructions were clear and complete, and, best of all, our range now works as it should. We couldn't be happier. Thanks, PartSelect.

Remove the racks
remove one nut that holds the heat deflector
3 screws that hold the igniter
remove the drawer
remove 2 screws holding a heat shield in place.
unplug old igniter and reinstall

Disconect power source; Remove oven racks, remove storage drawer under oven; remove floor of oven, remove flame deflector, remove three screws holding igniter cage and unplug faulty igniter. Reverse all steps for reassembly.

I used your instructions