AGS781LL-P1141275NLL Amana Range - Instructions

remove knobs and 2 screws from front panel, remove front panel. remove burner grates and caps. remove 8 screws (2 per burner base). remove each base and unplug wire. remove the top of the range. locate an remove old ingition module with bracket. on my model i did not need the new bracket. the new module fit right in the old one. unplug wires from old module and plug them into the new one in the same place they were in the old one. reverse the order to reassemble. new module does not make the same clikcing noise (not as fast as old one), but it lights on the first click. GRERT JOB PARTSELECT.!!! parts go to my house within 2 days...saved about $40-$50.

Unplugged the stove, removed all 4 burner discs from the stove top (2 screws each- WATCH YOU DONT STRIP HEADS) and disconnecting electrode wires ( DONT HAVE TO- IF YOU HAVE ENOUGH ROOM TO SIDE TOP UNIT OVER), unscrewed the old module, removed each of the 6 wires,one at a time and connected wires to the new module. Plug in stove to test before you screwed it into place, reinstalled the top unit , put the stove top in place,. Done!

found igniter not working, pulled up on door and it came off, lifted up bottom of oven and pulled out, removed wing nut on deflector to access igniter, removed igniter retaining bolts, unplugged connector, be careful not to let connector slip back in stove, and reverse process to install new igniter,, all took about twenty minutes, easy repair,

The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.

First turned off power to oven, Took burner out by lifting up and pulling out, then pulled out wires attached to the oven and igniter, removed two wire nuts and disconnected the wires then removed burner assembly from oven. With screwdriver and nut driver removed old igniter from housing and put new one in place, tightened up screws carried back to oven reattached wires with wirenuts and feed wires back into oven, then put burner back carefully silding igniter into hole in back of oven. Turned power back on to oven and worked nice. Took all of 15 mins to complete.

Bought a new one. . Three years later =)

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

Took the pan out of the bottom of the oven. Took the screws out of the assembly for the iron, disconnect the power wires under the stove and pull out the old iron. Reverse the proceedure but be careful with the new iron, it is very fragile. Connect the wires put the screws back and you are done. Make sure before you start the job that you unplug the appliance !!!!

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predrilled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

After removing the oven shelves, the burner cover came right up. The ignitor was in plain sight, and after removing the screws I pulled it straight out so I could get to the wire nuts. After swapping out the old igniter and sliding the cover over the new ignitor, the new piece slipped back into place in the oven. The screws were put back in, and the burner cover and shelves put back, and the oven works wonderfully again.

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

I found the ignitor was wired in series with the gas valve and wasn't letting enough voltage through to the gas valve to open it. I just unscrewed the ignitor and pulled it out.