AGS781LL-P1141275NLL Amana Range - Instructions

removed igniter and found porcelin split in half. JB welded both halves and put back into slot ,works fine now. Bought two extra in case.

Removed oven door by pulling off of hinges. Then removed screws that held door frame together. Replaced glass. Reassembled.

TURN OFF THE GAS SUPPLY & POWER TO THE STOVE. Disconnect the gas line & power source to the stove. Remove the complete counter top stove and place it upside down on a flat surface to enable you to remove all the surrounding small screws with a nut driver, then separate the bottom from the top accessing the retaining ring holding the ceramic electronic Ignition in place, remove the electric wire from the the old igniter. The most difficult part of the job was removing the retaining ring and installing the new ring.Job successfully completed.

We lived with the problem by using a long-reach butane torch lighter for three years after an appliance repairman told us the problem would be very costly to repair. Finally, we found the likely suspect when we happened onto PartSelect's website- the spark ignition module. The cost was just over $81 plus shipping. We ordered on Wednesday, it arrived on Friday by FedEx, and I installed it on Saturday morning. All the parts were included, the instructions were clear and complete, and, best of all, our range now works as it should. We couldn't be happier. Thanks, PartSelect.

Followed Instructions with part. Easy Install. However the problem not solved. I believe Oven Control defective (Worn Out). Replacement May not be available. Still looking. Thank You. RJC

Daughter and family came to visit Gramps for the weekend; Saturday morning, arose and opened a couple of cans of grand buscuits. Set aside to let rise then turned oven on to preheat. Came back later and oven did not work. Stove top worked, broiler worked, but no oven. What to do, didn't want to waste dough; perhaps salvage for dumplings, no; make poorboy doughnuts, no; Aha, lets use the outside gas grill, never done it, worth the try, remember old camping days except using gas. Worked like a charm, crisis over. Now back to oven. Since everything worked except the oven burner problem could be in the igniter, or oven control. Removed covers to burner assembly, pulled igniter, checked for continuity across the two leads. No go. Wait, need to check oven control, placed voltmeter across incomming leads, turned oven controls on and had voltage. Conclusion, igniter bad. Also noticed a small rust hole in the burner tube next to igniter, not good. Went on-line to PartsSelect, entered make and model number. No model but gave choice close to model. Viewed pictures, found one that came close. Placed order. Parts came in a very short time. Matched new parts to old. perfect. Removed burner tube and installed new one, one screw, simple. Wire nut the incomming leads to igniter and install, three screws, simple. Turned oven on, igniter glows bright, gas comes on, good blue flame, no need to adjust air inlet vents on burner tube. Turned off oven, replaced covers, then turned on oven, baked cornbread and enjoyed. Thanks, back in business. Dave

Removed burners and top cover to access ignition module.
Remove and replace module and reassemble stove.

Ceramic connectors were taken off the old igniter, pulled off old igniter and replaced in the same way the new igniter

Removed old ignightor and installed new one

I ordered the part and it was at my door in 2 days. I ordered the part on Wednesday thinking I would install it on the weekend after next. The part showed up on Friday. That was amazing considering I didn't sellect expeidited delivery. I didn't have a manual and have never tried this before so grade my attempt on a curve please. I started by unscrewing the screws closest to the hinge but quickly migrated to the entire face of the range. Pulled the range out and started unscrewing the screws on the side, and then the back. Figuring nothing was coming off and I still couldn't get to the hinge I stopped and regrouped. That's when my wife asked if she could help. I guess I looked distressed. By this time I had removed the drawer and had the range on it's back in the middle of the kitchen with little bowls of screws everywhere. My wife picked up the new hinge and looked it over. Then she started playing with the old hinge which was loose, but I couldn't get it out. She realized that you can remove the old hinge and install the new hinge without taking the whole thing apart. Where was she 30 minutes ago? The hinges came out and the new ones went it in about 10 minutes. It took me another 20 minutes to put back all of the screws I had taken off unnecessarily. Sometimes use your brains instead of a screwdriver. I have the best wife ever!

I bought the part and replaced it.

I ordered new racks to see if they weere out of alignment. The new racks fell from its tracks after the broiler was heated. It seems the oven cabinet is expanding with the heat and the rack width does not compensate for that. The new racks did not solve the problem so I do not know what can be done next. Any shelf support would have to be heat resistent. Replacing the oven cabinet is not a good option and no gauantee it wouldn't continue with this stove.

Removed burner with attached igniter assembly by raising forward legs from slots and pulling unit from rear support. Note: this is contrary to instruction #1 on installation instructions. Then followed the remaining instuctions 2 - 7 as written. Everything worked as planned.

Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones.
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!

ordered new broiler pan