ARGS7650E-P1130755NE Amana Range - Instructions

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

Thanks to this website I was able to quickly identify the needed part. A few days later I had it. To install the new part I had to open up the bottom inside of the oven to access the igniter assembly and remove the drawer to get to the connecting plug underneath. Four screws needed to be removed, unplugged the old part and plugged in the new part. Replaced the four screws to hold the igniter in place. Replaced the drawer and fired it up. Worked great!

My husband did the repair. He removed the wires and screws from the element and replaced with new part.

I found the ignitor was wired in series with the gas valve and wasn't letting enough voltage through to the gas valve to open it. I just unscrewed the ignitor and pulled it out.

1.) Trun Off Power
2.) Remove the Storage Drawer and the two (2) screws holding on the (Ignitor Plug) access cover-plate located in the back of the storage drawer access. (see page 15 if same model)
3.) Dissconnect the Ignitor Plug
4.) From the oven opening remove the three screws holding the Ignitor Holder.
5.) Remove the Ignitor and Holder from the oven by gently guiding the wires through the access hole
6.) Pull the Ignitor from the holder
7.) All Ignitors are extremelt fragile; install the new Ignitor into the Holder and make certain it is installed tight, mine was not. (Slight bending with my thumbs on the 1/4" flanges might hold it tighter if it is lose.)
8.)Reverse the process.
Note: One person here said they removed "ALL" the screws, maybe it was a different model, I only had to remove a total of "5" screws, two at the access cover plate and three at the Ignitor holder.
First time took me 20 minutes, if I needed to do it today, maybe 10.
Please also note that I didn't troubleshoot the Ignitor, as I didn't have a wrap-around amp meter, but the typical problem here would be the Ignitor, not the Gas Valve. Good Luck, pt

Removed the bottom drawer then removed the door - 2 screws. It would be hard to reach in oven with door still attached and it is simple to remove and put back on. Removed the racks and pan on bottom, which just lifts out. Removed 3 screws that hold bracket that contains igniter. The igniter plugs in and to access the plug you must remove a cover underneath the range. Once the drawer is out you have to crawl back in there to access the plug. I sent in my 14 year old for that. Make sure range is unplugged. Insert igniter in bracket and feed wire back down to plug in and reattach. Vacuumed oven out with a shop vac, etc. and it is a 30 min project.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Once I received the replacement part I simply reversed the process and it worked perfectly.

Shut off electric power. Removed bottom drawer.
Removed metal covers over burner in oven.
Removed 3 screws holding igniter in place. Disconnected wire plug under oven and pulled thru hole where igniter had been. Removed metal shield from defective igniter. Used care to place it on new igniter. Reinstalled everything.
My wife was observing and made me scrub under stove since I had the drawer removed.
I found the other repair stories very helpful in diaignosing my problem and ordering the right part. I ordered on Monday and received Wednesday afternoon normal delivery. Very good service.

First, I took out the racks from the oven. Next, I took out the black small square cover off the bottom of the stove, which gave me access to the oven ignitor. Then, I removed the screws to be able to take out the ignitor. Finally, I took the bottom drawer out to access the ignitor wire. I pulled the plastic connectors to disconnect the wire. I took the ignitor out and replaced with the new one. I put everything back in reverse order. The oven warmed up about 2 minutes after I turned it on.

you need to remove the shield then the tray under the burner and burner tube.then you can get to the plug. Just remember when putint it back you need to put the burner tube in first then the tray then you can screw the element back in place. replace all the screws. works great.

I assumed it was the igniter. The trick is to remove the bottom storage drawer for access to where the igniter is connected. You then need to run the wire up into the oven and mount next to the gas.

Turn off power to unit. Remove one nut inside bottom of oven to expose glow bar and igniter. Take 3 screws off of ignitor cover and remove it.

Pull out pan storage drawer to expose igniter plug connector. Unplug connector. Remove igniter.

Plug in new igniter and reverse the above instructions to reassemble.

This was a much easier repair than I thought it would be. I read online that, given the problems my oven was having, it was almost certainly the igniter that was the problem. It was - with the new igniter it works perfectly!

My husband took it apart then showed me how to put it back together. So I placed it in the metal holder and attatched all the screws.

Removed racks and pans from oven, removed 1 screw that housed the v shaped burner cover. Then I noticed the Igniter housing was held to back of oven with 3 small screws, removed 3 screws, and noticed the igniter just slid into the housing, but the connection would not come through back of unit. pulled out the lower tray to expose the underside of the oven and noticed 2 screws holding a metal cover, removed those and noticed connection to igniter, undid the connection, slid out the igniter and then just reversed the process to put back. It took me about 20 minutes, and that was only because I was being overly careful with the ceramic igniter, as the one in there just crumbled. Very easy job for anyone with even moderate skills. Ordered my part with assitance from a lady at parts express on Monday at noon, had the part delivered Tuesday at 3:00, had the oven back up and running fine by 3:30. Couldn't be happier, as this happened once before and the repairman charged me $185, this cost $48 and 15 minutes.
Unbelievable service and detailed help. I have this site bookmarked for anything moving forward.
Thanks

Thanks to previous reviews it was really easy! Popped cover plate off bottom of oven. Removed diffuser plate by using socket wrench to remove one bolt. Removed three screws (one on top; two on left side) of bracket. Good idea to use a magnetic screwdriver so they don't get lost! Slid igniter out of bracket- a bit tricky but gently eased it out. Slid new igniter in place taking care not to touch the element. Dropped wires and harness down next to old ones. Removed bottom drawer, crawled under and switched connections. Put everything back together. It did take a little longer for the new igniter to start the first time- about one minute- but now fires right up.

Part arrive only a couple of days after ordering, and installation time was less than to schedule a repairman! My only regret is that I didn't send my better half off for the entire afternoon so I could really make it out to be a big deal as my brother-in-law, the appliance repairman, made it out to be!