ARGS7650E-P1130755NE Amana Range - Instructions

very simple repair, the oven had the issue about ten years ago, just removed drawer ,removed two screws holding cover plate unhooked power and disconected plug. removed element screws and pulled out old element from holder and inserted new one. re attatched element holder, cover plate, and put drawer back in. works great !!!
My parts wrere shipped promptly and arraived in great condition, stove looks and works like new again

Removed oven grills and top of burner pan. This exposed the igniter. Removed 3 phillips head screws from igniter bracket. Slid old igniter out the back end. Removed utility drawer. Removed two screws from back pan covering igniter plug-in. Unplugged igniter, removed from range. Handling of igniter is tricky..do not touch black end. Slide new igniter into the bracket, feed wire with connector through hole in back (where igniter was removed from), install the three screws for the bracket (your new igniter is now secure), from the bottom, plug in the new connector it only goes on one way. Re-install pan with two screws. Put utility drawer back in..job is complete!!

ordered new broiler pan

Researched through this site to find part numbers and names. Youtubed it to see how to install the part. Ordered the exact part via this site and received it in only a day or two. Installed it in less than 15 minutes and the oven works amazing. It gets up to temp quickly and holds temp better than it has in years. Very satisfied!

Bought a new one. . Three years later =)

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased

I ordered new racks to see if they weere out of alignment. The new racks fell from its tracks after the broiler was heated. It seems the oven cabinet is expanding with the heat and the rack width does not compensate for that. The new racks did not solve the problem so I do not know what can be done next. Any shelf support would have to be heat resistent. Replacing the oven cabinet is not a good option and no gauantee it wouldn't continue with this stove.

I bought the part and replaced it.

First turned off power to oven, Took burner out by lifting up and pulling out, then pulled out wires attached to the oven and igniter, removed two wire nuts and disconnected the wires then removed burner assembly from oven. With screwdriver and nut driver removed old igniter from housing and put new one in place, tightened up screws carried back to oven reattached wires with wirenuts and feed wires back into oven, then put burner back carefully silding igniter into hole in back of oven. Turned power back on to oven and worked nice. Took all of 15 mins to complete.

1. Removed racks
2. Removed bottom cover
3. Removed screws holding ignitor
4. Removed storage draw
5. Removed cover over wires
6. Unplugged ignitor & placed with new
7. Put back together

Removed burner with attached igniter assembly by raising forward legs from slots and pulling unit from rear support. Note: this is contrary to instruction #1 on installation instructions. Then followed the remaining instuctions 2 - 7 as written. Everything worked as planned.

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predrilled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

1. Remove sliding shelves and lower pan sheild
2. Remove flame deflector
3 . Remove the 3 screws that hold the igniter in place. Insert the new cable and plug through the opening for connection in step 6. You may hve access to connector. If so skip to step 8.
4. Remove sliding storage drawer
5. Remove the sheetmetal pan to gain access to the igniter connector. It might help to have several blocks of wood the elevate the frront of the stove to allow more working clearance.
6. Disconnect old igniter, connect new igniter.
7. Replace pan and sliding drawer.
8. Remove old igniter from carrier and install new one.
9. Install igniter carrier to stove with 3 screws
10. Replace flame deflector and lower pan sheild.

It was really easy because I read information on your site. I only had to unscrew 3 screws, remove the old spark ignition electrode, replace the new one and then screw the 3 screws back. It was great

Took the pan out of the bottom of the oven. Took the screws out of the assembly for the iron, disconnect the power wires under the stove and pull out the old iron. Reverse the proceedure but be careful with the new iron, it is very fragile. Connect the wires put the screws back and you are done. Make sure before you start the job that you unplug the appliance !!!!