K45SSBFOB0 Whirlpool Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Peggy from Escondido, CA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic outer casing on tightening screw had broken
This is the tightening screw that holds the attachments into the motor unit of the mixer. Found your web site and reordered 2 replacement pieces (in case one breaks!). Very EZ and user friendly. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanislaw from San Antonio, TX
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken wire whip
no instructions necessary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONG from Elk Grove, CA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The worm gear was broken
I removed the pin from the outside shaft,then removed all screw around the body of the mixer,then removed the top case out,took 3 screws out from the the gear assembly case......punched the pin out of worm gear then release the little shaft out from the case,replaced a new one....then starting go backward till completely all assembled don't forget lube grease to all gears and test run good very smooth.........it's ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dale from AMSTERDAM, OH
- Parts Used:
- WPW10323373, WPW10112253, WP4162324
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
stripped worm gear
i disassembled the mixer until i could remove the worm gear; is in a housing that that includes another gear and shaft. make sure you have a magnetic tray to put parts in as you work or you will spend more time looking for parts than reassembling the mixer. once you have the gear housing out you will need a small diameter punch to drive out the pin that holds the gears in the housing(i used a 5/32 transfer punch.) make sure you punch the pin out where it will be caught or you will need to order that part because you will not find it. after knocking the pin out it is just a matter of removing the old gear, putting the new one in, and reversing the steps and getting everything reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from SALINAS, CA
- Parts Used:
- WPW10112253, WP9709280
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Kitchen Aid Mixer won't spin
Order the worm gear part number PS11748374.
Watch this video.
https://www.youtube.com/watch?v=VeCiivPt7hk
I would recommend two people if possible.
Watch this video.
https://www.youtube.com/watch?v=VeCiivPt7hk
I would recommend two people if possible.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reid from MONTICELLO, MN
- Parts Used:
- WPW10325124, WPW10119326
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Speed control not working properly
Replaced the speed control plate and phase control board and works well. Pay attention to speed control board spring and adjustment lever when reassembling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- E.F. from HUNTINGTN BCH, CA
- Parts Used:
- WPW10380496, WPW10330804, WPW10325124, WPW10119326
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Mixer would only run Full Fast. Could not determine cause or fault.
1. Removed the mixer back plate Cover. 2. Removed the Speed Control Plate and retained spring, wires and ground wire. 3. Removed the old Speed Control Plate screws. Noted Control Plate pitted contact. 4. Removed old Triac Phase Control Board. 5. Removed old Governor. 6. Installed new Governor. 7. Installed new Phase Control Board. 8. Installed new Speed Control Plate and retaining spring. 9. Reattached Speed Control Plate wires. 10. Adjusted Speed Control Plate Screws and set mixer speeds from Stir to maximum settings. 11. Replaced Motor Brushes on left and right side of mixer. 12. Reinstalled mixer back plate cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from SANTA FE, NM
- Parts Used:
- WP243368
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken beater shaft
Used the diagram on the website and a video
Totally worked!
Totally worked!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from JACKSON, TN
- Parts Used:
- WP9704329
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old wire whip was broken
Just put on the new whip...exactly like old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mrs Brenda from LYNNWOOD, WA
- Parts Used:
- WP9709194
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Screw cracked on the front of the mixer
Skewer the screw in with my fingers,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from FAIRFIELD, CT
- Parts Used:
- WPW10191926
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old screw cap wore out and would not hold bowl when mixing heavy batters.
Unscrewed old Screw Cap, tapped it out with hammer. Replaced with new screw cap that was slightly different and tight. Tapped it in with piece of wood over it and hammered it on. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from RICHMOND HILL, GA
- Parts Used:
- WPW10380496, WP3184212, WP116287, WP116286
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
None
I removed the spring loaded brush screw on the side of my mixer and lost it the next day. I found a schematic of this part on your website and ordered the four pieces that make up the brush screw(?). They arrived in just a few days and I referred back to the schematic to put it together. I then popped it in my mixer, screwed it down, plugged her in and away we go! Easiest repair I’ve ever done! I’m a 70 year old retired lady and not very handy, but this was an easy fix! Thank you, PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from West Stockbridge, MA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Base plate destored
I removed three screws, pulled off the old base plate.
Put new base plate in place and replaced the screws
Put new base plate in place and replaced the screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from AURORA, CO
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bowel would come out of screwcap when making dough for pasta
The repair was easy only requiring a phillips head screw driver to remove the old screw cap. The new screw cap fit snuggly and required a little downward pressure from my hand to seat it. Then I simply tightened the screws. Good as new for this 30+ year old mixer. My wife loves this mixer that was given to her by her Aunt. Glad we could keep it going.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SUQUAMISH, WA
- Parts Used:
- WPW10112253, WP9705444
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Replaced worn out gear
Fairly easy if you have done it once before.
Was this instruction helpful to you?
Thank you for voting!